Dépouillements

Buckling and postbuckling behavior of cross - ply composite plate subjected to nonuniform in - plane loads / Sarat Kumar Panda in Journal of engineering mechanics, Vol. 137 N° 9 (Septembre 2011) 

Public ISBD [article]  in Journal of engineering mechanics > Vol. 137 N° 9 (Septembre 2011) . - pp.589-597 Titre : Buckling and postbuckling behavior of cross - ply composite plate subjected to nonuniform in - plane loads Type de document : texte imprimé Auteurs : Sarat Kumar Panda, Auteur ; L. S. Ramachandra, Auteur Année de publication : 2011 Article en page(s) : pp.589-597 Note générale : Mécanique appliquée Langues : Anglais (eng) Mots-clés : Buckling  loads  Postbuckling  analysis  Nonuniform  in-plane  loads  Ritz  method  Galerkin  method Résumé : This paper presents a study of buckling and postbuckling behaviour of simply supported composite plates subjected to nonuniform in-plane loading. The mathematical model is based on higher order shear deformation theory incorporating von Kármán nonlinear strain displacement relations. Because the applied in-plane edge load is nonuniform, in the first step the plane elasticity problem is solved to evaluate the stress distribution within the prebuckling range. Using these stress distributions, the governing equations for postbuckling analysis of composite plates are obtained through the theorem of minimum potential energy. Adopting Galerkin’s approximation, the governing nonlinear partial differential equations are reduced into a set of nonlinear algebraic equations in the case of postbuckling analysis, and homogeneous linear algebraic equations in the case of buckling analysis. The critical buckling load is obtained from the solution of associated linear eigenvalue problem. Postbuckling equilibrium paths are obtained by solving nonlinear algebraic equations employing the Newton-Raphson iterative scheme. Explicit expressions for the plate in-plane stress distributions within the prebuckling range are reported for isotropic and composite plates subjected to parabolic in-plane edge loading. Buckling loads are determined for three plate aspect ratios (a/b = 0.5, 1, 1.5) and three different types of in-plane load distributions. The effect of shear deformation on the buckling loads of composite plate is reported. The present buckling results are compared with previously published results wherever possible. DEWEY : 620.1 ISSN : 0733-9399 En ligne : http://ascelibrary.org/emo/resource/1/jenmdt/v137/i9/p589_s1?isAuthorized=no [article] Buckling and postbuckling behavior of cross - ply composite plate subjected to nonuniform in - plane loads [texte imprimé] / Sarat Kumar Panda, Auteur ; L. S. Ramachandra, Auteur . - 2011 . - pp.589-597. Mécanique appliquée Langues : Anglais (eng) in Journal of engineering mechanics > Vol. 137 N° 9 (Septembre 2011) . - pp.589-597 Mots-clés : Buckling  loads  Postbuckling  analysis  Nonuniform  in-plane  loads  Ritz  method  Galerkin  method Résumé : This paper presents a study of buckling and postbuckling behaviour of simply supported composite plates subjected to nonuniform in-plane loading. The mathematical model is based on higher order shear deformation theory incorporating von Kármán nonlinear strain displacement relations. Because the applied in-plane edge load is nonuniform, in the first step the plane elasticity problem is solved to evaluate the stress distribution within the prebuckling range. Using these stress distributions, the governing equations for postbuckling analysis of composite plates are obtained through the theorem of minimum potential energy. Adopting Galerkin’s approximation, the governing nonlinear partial differential equations are reduced into a set of nonlinear algebraic equations in the case of postbuckling analysis, and homogeneous linear algebraic equations in the case of buckling analysis. The critical buckling load is obtained from the solution of associated linear eigenvalue problem. Postbuckling equilibrium paths are obtained by solving nonlinear algebraic equations employing the Newton-Raphson iterative scheme. Explicit expressions for the plate in-plane stress distributions within the prebuckling range are reported for isotropic and composite plates subjected to parabolic in-plane edge loading. Buckling loads are determined for three plate aspect ratios (a/b = 0.5, 1, 1.5) and three different types of in-plane load distributions. The effect of shear deformation on the buckling loads of composite plate is reported. The present buckling results are compared with previously published results wherever possible. DEWEY : 620.1 ISSN : 0733-9399 En ligne : http://ascelibrary.org/emo/resource/1/jenmdt/v137/i9/p589_s1?isAuthorized=no

Wave propagation in a pipe pile for low - strain integrity testing / Xuanming Ding in Journal of engineering mechanics, Vol. 137 N° 9 (Septembre 2011) 

Public ISBD [article]  in Journal of engineering mechanics > Vol. 137 N° 9 (Septembre 2011) . - pp.598-609 Titre : Wave propagation in a pipe pile for low - strain integrity testing Type de document : texte imprimé Auteurs : Xuanming Ding, Auteur ; Hanlong Liu, Auteur ; Jinyuan Liu, Auteur Année de publication : 2011 Article en page(s) : pp.598-609 Note générale : Mécanique appliquée Langues : Anglais (eng) Mots-clés : Wave  propagation  Tubular  structure  Pipe  pile  Low-strain  integrity  testing  Analytical  solution  Stress  wave Résumé : This paper presents an analytical solution methodology for a tubular structure subjected to a transient point loading in low-strain integrity testing. The three-dimensional effects on the pile head and the applicability of plane-section assumption are the main problems in low-strain integrity testing on a large-diameter tubular structure, such as a pipe pile. The propagation of stress waves in a tubular structure cannot be expressed by one-dimensional wave theory on the basis of plane-section assumption. This paper establishes the computational model of a large-diameter tubular structure with a variable wave impedance section, where the soil resistance is simulated by the Winkler model, and the exciting force is simulated with semisinusoidal impulse. The defects are classified into the change in the wall thickness and Young’s modulus. Combining the boundary and initial conditions, a frequency-domain analytical solution of a three-dimensional wave equation is deduced from the Fourier transform method and the separation of variables methods. On the basis of the frequency-domain analytic solution, the time-domain response is obtained from the inverse Fourier transform method. The three-dimensional finite-element models are used to verify the validity of analytical solutions for both an intact and a defective pipe pile. The analytical solutions obtained from frequency domain are compared with the finite-element method (FEM) results on both pipe piles in this paper, including the velocity time history, peak value, incident time arrival, and reflected wave crests. A case study is shown and the characteristics of velocity response time history on the top of an intact and a defective pile are investigated. The comparisons show that the analytical solution derived in this paper is reliable for application in the integrity testing on a tubular structure. DEWEY : 620.1 ISSN : 0733-9399 En ligne : http://ascelibrary.org/emo/resource/1/jenmdt/v137/i9/p598_s1?isAuthorized=no [article] Wave propagation in a pipe pile for low - strain integrity testing [texte imprimé] / Xuanming Ding, Auteur ; Hanlong Liu, Auteur ; Jinyuan Liu, Auteur . - 2011 . - pp.598-609. Mécanique appliquée Langues : Anglais (eng) in Journal of engineering mechanics > Vol. 137 N° 9 (Septembre 2011) . - pp.598-609 Mots-clés : Wave  propagation  Tubular  structure  Pipe  pile  Low-strain  integrity  testing  Analytical  solution  Stress  wave Résumé : This paper presents an analytical solution methodology for a tubular structure subjected to a transient point loading in low-strain integrity testing. The three-dimensional effects on the pile head and the applicability of plane-section assumption are the main problems in low-strain integrity testing on a large-diameter tubular structure, such as a pipe pile. The propagation of stress waves in a tubular structure cannot be expressed by one-dimensional wave theory on the basis of plane-section assumption. This paper establishes the computational model of a large-diameter tubular structure with a variable wave impedance section, where the soil resistance is simulated by the Winkler model, and the exciting force is simulated with semisinusoidal impulse. The defects are classified into the change in the wall thickness and Young’s modulus. Combining the boundary and initial conditions, a frequency-domain analytical solution of a three-dimensional wave equation is deduced from the Fourier transform method and the separation of variables methods. On the basis of the frequency-domain analytic solution, the time-domain response is obtained from the inverse Fourier transform method. The three-dimensional finite-element models are used to verify the validity of analytical solutions for both an intact and a defective pipe pile. The analytical solutions obtained from frequency domain are compared with the finite-element method (FEM) results on both pipe piles in this paper, including the velocity time history, peak value, incident time arrival, and reflected wave crests. A case study is shown and the characteristics of velocity response time history on the top of an intact and a defective pile are investigated. The comparisons show that the analytical solution derived in this paper is reliable for application in the integrity testing on a tubular structure. DEWEY : 620.1 ISSN : 0733-9399 En ligne : http://ascelibrary.org/emo/resource/1/jenmdt/v137/i9/p598_s1?isAuthorized=no

Anisotropic damage model for concrete / J. J. C. Pituba in Journal of engineering mechanics, Vol. 137 N° 9 (Septembre 2011) 

Public ISBD [article]  in Journal of engineering mechanics > Vol. 137 N° 9 (Septembre 2011) . - pp.610-624 Titre : Anisotropic damage model for concrete Type de document : texte imprimé Auteurs : J. J. C. Pituba, Auteur ; G. R. Fernandes, Auteur Année de publication : 2011 Article en page(s) : pp.610-624 Note générale : Mécanique appliquée Langues : Anglais (eng) Mots-clés : Damage  Anisotropy  Constitutive  models  Two-dimensional  analysis  Concrete  structures Résumé : In this paper, a damage constitutive model accounting for induced anisotropy and bimodular elastic response is applied to two-dimensional analysis of reinforced concrete structures. Initially, a constitutive model for the concrete is presented, where the material is assumed as an initial elastic isotropic medium presenting anisotropy and bimodular response (distinct elastic responses, whether tension or compression stress states, prevail) induced by damage. Two damage tensors govern the stiffness under prevailing tension or compression stress states. Criteria are then proposed to characterize the dominant states. Finally, the proposed model is used in plane analysis of reinforced concrete beams to show its potential for use and to discuss its limitations. DEWEY : 620.1 ISSN : 0733-9399 En ligne : http://ascelibrary.org/emo/resource/1/jenmdt/v137/i9/p610_s1?isAuthorized=no [article] Anisotropic damage model for concrete [texte imprimé] / J. J. C. Pituba, Auteur ; G. R. Fernandes, Auteur . - 2011 . - pp.610-624. Mécanique appliquée Langues : Anglais (eng) in Journal of engineering mechanics > Vol. 137 N° 9 (Septembre 2011) . - pp.610-624 Mots-clés : Damage  Anisotropy  Constitutive  models  Two-dimensional  analysis  Concrete  structures Résumé : In this paper, a damage constitutive model accounting for induced anisotropy and bimodular elastic response is applied to two-dimensional analysis of reinforced concrete structures. Initially, a constitutive model for the concrete is presented, where the material is assumed as an initial elastic isotropic medium presenting anisotropy and bimodular response (distinct elastic responses, whether tension or compression stress states, prevail) induced by damage. Two damage tensors govern the stiffness under prevailing tension or compression stress states. Criteria are then proposed to characterize the dominant states. Finally, the proposed model is used in plane analysis of reinforced concrete beams to show its potential for use and to discuss its limitations. DEWEY : 620.1 ISSN : 0733-9399 En ligne : http://ascelibrary.org/emo/resource/1/jenmdt/v137/i9/p610_s1?isAuthorized=no

Chemo - mechanical modeling requirements for the assessment of concrete structure service life / L. Buffo-Lacarrière in Journal of engineering mechanics, Vol. 137 N° 9 (Septembre 2011) 

Public ISBD [article]  in Journal of engineering mechanics > Vol. 137 N° 9 (Septembre 2011) . - pp.625-633 Titre : Chemo - mechanical modeling requirements for the assessment of concrete structure service life Type de document : texte imprimé Auteurs : L. Buffo-Lacarrière, Auteur ; A. Sellier, Auteur Année de publication : 2011 Article en page(s) : pp.625-633 Note générale : Mécanique appliquée Langues : Anglais (eng) Mots-clés : Leaching  Hydration  Constitutive  relations  Creep  Damage  Chemo-mechanical  coupling  Concrete  structures Résumé : This paper deals with the formulation requirements for the finite-element modeling of the life cycle of concrete structures subjected to chemical evolution combined with mechanical loading. In particular, it considers the coupling of chemical evolution with nonlinear mechanical behavior combining creep and damage. Not only do the parameters of the mechanical model have to be adapted to the effect of chemical evolution, but also the chemical effects on the internal mechanical state variables of the chemical evolution have to be carefully considered. These two couplings are discussed and clarified in a general formulation useful for a finite-element implementation of a mechanical behavior law intended for chemo-mechanical applications. The approach is illustrated through a model developed to assess the mechanical behavior of concrete structures subjected to hydration and then to leaching during their service life. Hydration and leaching need to be considered together in the same model to study how damage of the concrete at its early age can affect its response in the long term. The model is implemented in a finite-element code and applied, first to the simulation of an early age creep test and then to the prediction of the very-long-term mechanical behavior of a nuclear waste storage facility. DEWEY : 620.1 ISSN : 0733-9399 En ligne : http://ascelibrary.org/emo/resource/1/jenmdt/v137/i9/p625_s1?isAuthorized=no [article] Chemo - mechanical modeling requirements for the assessment of concrete structure service life [texte imprimé] / L. Buffo-Lacarrière, Auteur ; A. Sellier, Auteur . - 2011 . - pp.625-633. Mécanique appliquée Langues : Anglais (eng) in Journal of engineering mechanics > Vol. 137 N° 9 (Septembre 2011) . - pp.625-633 Mots-clés : Leaching  Hydration  Constitutive  relations  Creep  Damage  Chemo-mechanical  coupling  Concrete  structures Résumé : This paper deals with the formulation requirements for the finite-element modeling of the life cycle of concrete structures subjected to chemical evolution combined with mechanical loading. In particular, it considers the coupling of chemical evolution with nonlinear mechanical behavior combining creep and damage. Not only do the parameters of the mechanical model have to be adapted to the effect of chemical evolution, but also the chemical effects on the internal mechanical state variables of the chemical evolution have to be carefully considered. These two couplings are discussed and clarified in a general formulation useful for a finite-element implementation of a mechanical behavior law intended for chemo-mechanical applications. The approach is illustrated through a model developed to assess the mechanical behavior of concrete structures subjected to hydration and then to leaching during their service life. Hydration and leaching need to be considered together in the same model to study how damage of the concrete at its early age can affect its response in the long term. The model is implemented in a finite-element code and applied, first to the simulation of an early age creep test and then to the prediction of the very-long-term mechanical behavior of a nuclear waste storage facility. DEWEY : 620.1 ISSN : 0733-9399 En ligne : http://ascelibrary.org/emo/resource/1/jenmdt/v137/i9/p625_s1?isAuthorized=no

Exemplaires

Bibliothèque Ecole Nationale Polytechnique d'Alger

Accueil

Se connecter

Météo

Adresse