Metallic interconnects for solid oxide fuel cell: Performance of reactive element oxide coating during long time exposure / S. Fontana in Materials and corrosion, Vol. 62 N° 7 (Juillet 2011)  

Public ISBD [article]  inMaterials and corrosion > Vol. 62 N° 7 (Juillet 2011) . - pp. 650–658 Titre : Metallic interconnects for solid oxide fuel cell: Performance of reactive element oxide coating during long time exposure Type de document : texte imprimé Auteurs : S. Fontana, Auteur ; S. Chevalier, Auteur ; G. Caboche, Auteur Année de publication : 2011 Article en page(s) : pp. 650–658 Note générale : Génie Mécanique Langues : Anglais (eng) Mots-clés : Metallic interconnect MOCVD Reactive element SOFC Index. décimale : 620.1 Essais des matériaux. Défauts des matériaux. Protection des matériaux Résumé : One of challenges in improving the performance and cost-effectiveness of SOFCs (solid oxide fuel cells) is the development of suitable interconnects materials. Chromia-forming alloys and especially ferritic stainless steels, like Crofer22APU, are considered to be among the most promising candidate materials as interconnects in SOFC stacks. However, the performance of chromia-forming materials can be limited by the low electronic conductivity of the oxide scale (high ASR – area specific resistance – value). Such degradation are unacceptable regarding the long-term operation (>40 000 h). A previous study 1 demonstrated that in air, the addition of a nanometric reactive element oxide (La2O3) layer applied by metal organic chemical vapor deposition (MOCVD) drastically improved both corrosion rate and electrical properties of Crofer22APU and Haynes230 alloys for 100 h at 800 °C. In this present study coating performances were checked after 10 months (7500 h) and 20 months (15 000 h) at 800 °C in air. The corrosion products were carefully analyzed by SEM, EDX, and XRD. ASR measurements are realized after long time exposure. This study demonstrates that the Crofer22APU alloy has a good oxidation resistance after 15 000 h in air but this alloy has an ASR value equal to 0.370 Ω cm2. The coatings composed of a thin reactive element oxide such as La2O3 resulted in an important improvement in the high temperature oxidation resistance; the ASR values are equal to 0.154 Ω cm2. Haynes230 alloy has a better oxidation resistance but the formation of an insulating Al2O3/SiO2 layer could be detrimental. DEWEY : 620.1 ISSN : 0947-5117 En ligne : http://onlinelibrary.wiley.com/doi/10.1002/maco.201005857/abstract [article] Metallic interconnects for solid oxide fuel cell: Performance of reactive element oxide coating during long time exposure [texte imprimé] / S. Fontana, Auteur ; S. Chevalier, Auteur ; G. Caboche, Auteur . - 2011 . - pp. 650–658. Génie Mécanique Langues : Anglais (eng) in Materials and corrosion > Vol. 62 N° 7 (Juillet 2011) . - pp. 650–658 Mots-clés : Metallic interconnect MOCVD Reactive element SOFC Index. décimale : 620.1 Essais des matériaux. Défauts des matériaux. Protection des matériaux Résumé : One of challenges in improving the performance and cost-effectiveness of SOFCs (solid oxide fuel cells) is the development of suitable interconnects materials. Chromia-forming alloys and especially ferritic stainless steels, like Crofer22APU, are considered to be among the most promising candidate materials as interconnects in SOFC stacks. However, the performance of chromia-forming materials can be limited by the low electronic conductivity of the oxide scale (high ASR – area specific resistance – value). Such degradation are unacceptable regarding the long-term operation (>40 000 h). A previous study 1 demonstrated that in air, the addition of a nanometric reactive element oxide (La2O3) layer applied by metal organic chemical vapor deposition (MOCVD) drastically improved both corrosion rate and electrical properties of Crofer22APU and Haynes230 alloys for 100 h at 800 °C. In this present study coating performances were checked after 10 months (7500 h) and 20 months (15 000 h) at 800 °C in air. The corrosion products were carefully analyzed by SEM, EDX, and XRD. ASR measurements are realized after long time exposure. This study demonstrates that the Crofer22APU alloy has a good oxidation resistance after 15 000 h in air but this alloy has an ASR value equal to 0.370 Ω cm2. The coatings composed of a thin reactive element oxide such as La2O3 resulted in an important improvement in the high temperature oxidation resistance; the ASR values are equal to 0.154 Ω cm2. Haynes230 alloy has a better oxidation resistance but the formation of an insulating Al2O3/SiO2 layer could be detrimental. DEWEY : 620.1 ISSN : 0947-5117 En ligne : http://onlinelibrary.wiley.com/doi/10.1002/maco.201005857/abstract

Exemplaires

Code-barres	Cote	Support	Localisation	Section	Disponibilité
aucun exemplaire