Documents disponibles écrits par cet auteur

Demonstration of a palm-sized 30 W air-to-power turbine generator / S. Sato in Transactions of the ASME . Journal of engineering for gas turbines and power, Vol. 133 N° 10 (Octobre 2011) 

Public ISBD [article]  in Transactions of the ASME . Journal of engineering for gas turbines and power > Vol. 133 N° 10 (Octobre 2011) . - 10 p. Titre : Demonstration of a palm-sized 30 W air-to-power turbine generator Type de document : texte imprimé Auteurs : S. Sato, Auteur ; S. Jovanovic, Auteur ; J. Lang, Auteur Année de publication : 2011 Article en page(s) : 10 p. Note générale : Génie mécanique Langues : Anglais (eng) Mots-clés : Turbines  Turbogenerators Index. décimale : 620.1 Essais des matériaux. Défauts des matériaux. Protection des matériaux Résumé : A compact, high power density turbo-generator system was conceived, designed, and experimentally tested. The air-to-power (A2P) device with a nominal design point of 50 W electric power output operates on high pressure air such as from a plant pneumatic system or from a portable bottle of pressurized air. A concept design study was first carried out to explore the design space for a range of output power at cost efficiency levels specified in collaboration with industry. The cost efficiency is defined as the cost of electrical power over the cost of pressurized air. The key challenge in the design is the relatively low power demand of 50 W while operating at high supply pressures of nominally 5–6 bars. To meet the cost efficiency goal under these conditions, a high-speed turbine and generator (~450,000 rpm) are required with small blade span (~200 µm), minimizing the mass flow while achieving the highest possible turbine performance. Since turbines with such small turbomachinery blading are not commercially available, a silicon-based micro electro mechanical systems (MEMS) turbine was designed using 2D and 3D computational fluid dynamics (CFD) computations. To reduce the development time, existing and previously demonstrated custom-made generator and ceramic ball bearing technology were used, resulting in a compact A2P proof-of-concept demonstration. The cylindrical device of 35 mm diameter resembles a tube fitting with a standard M24 adapter. Without load, a top turbine speed of 475,000 rpm was demonstrated, exceeding the design specification. Using load resistors, the proof-of-concept A2P device achieved 30 W of electrical power at 360,000 rpm and a turbine efficiency of 47%, meeting the cost efficiency goal. Higher speeds under load could not be achieved due to thrust load limitations of the off-shelf ball bearings. The demonstrated performance is in good agreement with the projected CFD based predictions. To the authors' knowledge, this is the first successful demonstration of a self-contained, 50 W class turbo-generator of hybrid architecture where a MEMS turbine disk is joined with a precision machined titanium shaft and aluminum housing. DEWEY : 620.1 ISSN : 0742-4795 En ligne : http://asmedl.aip.org/getabs/servlet/GetabsServlet?prog=normal&id=JETPEZ00013300 [...] [article] Demonstration of a palm-sized 30 W air-to-power turbine generator [texte imprimé] / S. Sato, Auteur ; S. Jovanovic, Auteur ; J. Lang, Auteur . - 2011 . - 10 p. Génie mécanique Langues : Anglais (eng) in Transactions of the ASME . Journal of engineering for gas turbines and power > Vol. 133 N° 10 (Octobre 2011) . - 10 p. Mots-clés : Turbines  Turbogenerators Index. décimale : 620.1 Essais des matériaux. Défauts des matériaux. Protection des matériaux Résumé : A compact, high power density turbo-generator system was conceived, designed, and experimentally tested. The air-to-power (A2P) device with a nominal design point of 50 W electric power output operates on high pressure air such as from a plant pneumatic system or from a portable bottle of pressurized air. A concept design study was first carried out to explore the design space for a range of output power at cost efficiency levels specified in collaboration with industry. The cost efficiency is defined as the cost of electrical power over the cost of pressurized air. The key challenge in the design is the relatively low power demand of 50 W while operating at high supply pressures of nominally 5–6 bars. To meet the cost efficiency goal under these conditions, a high-speed turbine and generator (~450,000 rpm) are required with small blade span (~200 µm), minimizing the mass flow while achieving the highest possible turbine performance. Since turbines with such small turbomachinery blading are not commercially available, a silicon-based micro electro mechanical systems (MEMS) turbine was designed using 2D and 3D computational fluid dynamics (CFD) computations. To reduce the development time, existing and previously demonstrated custom-made generator and ceramic ball bearing technology were used, resulting in a compact A2P proof-of-concept demonstration. The cylindrical device of 35 mm diameter resembles a tube fitting with a standard M24 adapter. Without load, a top turbine speed of 475,000 rpm was demonstrated, exceeding the design specification. Using load resistors, the proof-of-concept A2P device achieved 30 W of electrical power at 360,000 rpm and a turbine efficiency of 47%, meeting the cost efficiency goal. Higher speeds under load could not be achieved due to thrust load limitations of the off-shelf ball bearings. The demonstrated performance is in good agreement with the projected CFD based predictions. To the authors' knowledge, this is the first successful demonstration of a self-contained, 50 W class turbo-generator of hybrid architecture where a MEMS turbine disk is joined with a precision machined titanium shaft and aluminum housing. DEWEY : 620.1 ISSN : 0742-4795 En ligne : http://asmedl.aip.org/getabs/servlet/GetabsServlet?prog=normal&id=JETPEZ00013300 [...]