Documents disponibles écrits par cet auteur

Plasto-elastohydrodynamic lubrication (PEHL) in point contacts / Ning Ren in Transactions of the ASME . Journal of tribology, Vol. 132 N° 3 (Juillet 2010) 

Public ISBD [article]  in Transactions of the ASME . Journal of tribology > Vol. 132 N° 3 (Juillet 2010) . - 11 p. Titre : Plasto-elastohydrodynamic lubrication (PEHL) in point contacts Type de document : texte imprimé Auteurs : Ning Ren, Auteur ; Dong Zhu, Auteur ; W. W. Chen, Auteur Année de publication : 2011 Article en page(s) : 11 p. Note générale : Tribology Langues : Anglais (eng) Mots-clés : Lubrication  Mechanical  contact  Plastic  deformation  Surface  roughness  Work  hardening Index. décimale : 621.5 Energie pneumatique. Machinerie et outils. Réfrigération Résumé : Elastohydrodynamic lubrication (EHL) is an important branch of the lubrication theory, describing lubrication mechanisms in nonconformal contacts widely found in many mechanical components such as various gears, rolling bearings, cams and followers, metal-rolling tools, traction drives, and continuous variable transmissions. These components often transmit substantial power under heavy loading conditions. Also, the roughness of machined surfaces is usually of the same order of magnitude as, or greater than, the estimated average EHL film thickness. Consequently, most components operate in mixed lubrication regime with significant asperity contacts. Due to very high pressure concentrated in small areas, resulted from either heavy external loading or severe asperity contacts, or often a combination of both, subsurface stresses may exceed the material yield limit, causing considerable plastic deformation, which may not only permanently change the surface profiles and contact geometry but also alter material properties through work hardening as well. In the present study, a three-dimensional plasto-elastohydrodynamic lubrication (PEHL) model has been developed by taking into account plastic deformation and material work-hardening. The effects of surface/subsurface plastic deformation on lubricant film thickness, surface pressure distribution, and subsurface stress field have been investigated. This paper briefly describes the newly developed PEHL model and presents preliminary results and observed basic behavior of the PEHL in smooth-surface point contacts, in comparison with those from corresponding EHL solutions under the same conditions. The results indicate that plastic deformation may greatly affect contact and lubrication characteristics, resulting in significant reductions in lubricant film thickness, peak surface pressure and maximum subsurface stresses. DEWEY : 621.5 ISSN : 0742-4787 En ligne : http://scitation.aip.org/getabs/servlet/GetabsServlet?prog=normal&id=JOTRE900013 [...] [article] Plasto-elastohydrodynamic lubrication (PEHL) in point contacts [texte imprimé] / Ning Ren, Auteur ; Dong Zhu, Auteur ; W. W. Chen, Auteur . - 2011 . - 11 p. Tribology Langues : Anglais (eng) in Transactions of the ASME . Journal of tribology > Vol. 132 N° 3 (Juillet 2010) . - 11 p. Mots-clés : Lubrication  Mechanical  contact  Plastic  deformation  Surface  roughness  Work  hardening Index. décimale : 621.5 Energie pneumatique. Machinerie et outils. Réfrigération Résumé : Elastohydrodynamic lubrication (EHL) is an important branch of the lubrication theory, describing lubrication mechanisms in nonconformal contacts widely found in many mechanical components such as various gears, rolling bearings, cams and followers, metal-rolling tools, traction drives, and continuous variable transmissions. These components often transmit substantial power under heavy loading conditions. Also, the roughness of machined surfaces is usually of the same order of magnitude as, or greater than, the estimated average EHL film thickness. Consequently, most components operate in mixed lubrication regime with significant asperity contacts. Due to very high pressure concentrated in small areas, resulted from either heavy external loading or severe asperity contacts, or often a combination of both, subsurface stresses may exceed the material yield limit, causing considerable plastic deformation, which may not only permanently change the surface profiles and contact geometry but also alter material properties through work hardening as well. In the present study, a three-dimensional plasto-elastohydrodynamic lubrication (PEHL) model has been developed by taking into account plastic deformation and material work-hardening. The effects of surface/subsurface plastic deformation on lubricant film thickness, surface pressure distribution, and subsurface stress field have been investigated. This paper briefly describes the newly developed PEHL model and presents preliminary results and observed basic behavior of the PEHL in smooth-surface point contacts, in comparison with those from corresponding EHL solutions under the same conditions. The results indicate that plastic deformation may greatly affect contact and lubrication characteristics, resulting in significant reductions in lubricant film thickness, peak surface pressure and maximum subsurface stresses. DEWEY : 621.5 ISSN : 0742-4787 En ligne : http://scitation.aip.org/getabs/servlet/GetabsServlet?prog=normal&id=JOTRE900013 [...]

Three-dimensional plasto-elastohydrodynamic lubrication (PEHL) for surfaces with irregularities / Ning Ren in Transactions of the ASME . Journal of tribology, Vol. 133 N° 3 (Juillet 2011) 

Public ISBD [article]  in Transactions of the ASME . Journal of tribology > Vol. 133 N° 3 (Juillet 2011) . - 10 p. Titre : Three-dimensional plasto-elastohydrodynamic lubrication (PEHL) for surfaces with irregularities Type de document : texte imprimé Auteurs : Ning Ren, Auteur ; Dong Zhu, Auteur ; Q. Jane Wang, Auteur Année de publication : 2012 Article en page(s) : 10 p. Note générale : Tribology Langues : Anglais (eng) Mots-clés : Elastodynamics  Elastoplasticity  Lubrication  Plastic  deformation  Point  contacts  Stress-strain  relations  Surface  roughness Index. décimale : 621.5 Energie pneumatique. Machinerie et outils. Réfrigération Résumé : Elastohydrodynamic lubrication (EHL) is one of the most common types of lubrication, which widely exists in many machine elements such as gears, rolling bearings, cams and followers, metal rolling tools, and continuous variable transmissions. These components often transmit substantial power under heavy loading conditions that may possibly induce plastic deformation of contacting surfaces. Moreover, the roughness of machined surfaces is usually of the same order of magnitude as, or greater than, the average EHL film thickness. Consequently, most components operate in mixed lubrication with considerable asperity contacts, which may result in localized pressure peaks much higher than the Hertzian pressure, causing subsurface stress concentrations possibly exceeding the material yield limit. Plastic deformation, therefore, often takes place, which not only permanently changes the surface profiles and contact geometry, but alters material properties through work-hardening as well. Available mixed EHL models, however, do not consider plastic deformation, often yielding unrealistically high pressure spikes and subsurface stresses around asperity contact locations. Recently, a three-dimensional (3D) plasto-elastohydrodynamic lubrication (PEHL) model has been developed for investigating the effects of plastic deformation and material work-hardening on the EHL characteristics and subsurface stress/strain fields. The present paper is a continuation of the previous work done by Ren et al. (2010, “PEHL in point contacts,” ASME J. Tribol., 132(3), pp. 031501) that focused on model development and validation, as well as investigation of fundamental PEHL mechanisms in smooth surface contacts. This part of the study is mainly on the PEHL behavior involving simple surface irregularities, such as a single asperity or dent, which can be considered as basic elements of more complicated surface roughness. It is found that considerable plastic deformation may occur due to the pressure peaks caused by the surface irregularity, even though sometimes external loading is not heavy and the irregularity is concave. The plastic deformation may significantly affect contact and lubrication characteristics, resulting in considerable reductions in peak pressure and maximum subsurface stresses. DEWEY : 621.5 ISSN : 0742-4787 En ligne : http://scitation.aip.org/getabs/servlet/GetabsServlet?prog=normal&id=JOTRE900013 [...] [article] Three-dimensional plasto-elastohydrodynamic lubrication (PEHL) for surfaces with irregularities [texte imprimé] / Ning Ren, Auteur ; Dong Zhu, Auteur ; Q. Jane Wang, Auteur . - 2012 . - 10 p. Tribology Langues : Anglais (eng) in Transactions of the ASME . Journal of tribology > Vol. 133 N° 3 (Juillet 2011) . - 10 p. Mots-clés : Elastodynamics  Elastoplasticity  Lubrication  Plastic  deformation  Point  contacts  Stress-strain  relations  Surface  roughness Index. décimale : 621.5 Energie pneumatique. Machinerie et outils. Réfrigération Résumé : Elastohydrodynamic lubrication (EHL) is one of the most common types of lubrication, which widely exists in many machine elements such as gears, rolling bearings, cams and followers, metal rolling tools, and continuous variable transmissions. These components often transmit substantial power under heavy loading conditions that may possibly induce plastic deformation of contacting surfaces. Moreover, the roughness of machined surfaces is usually of the same order of magnitude as, or greater than, the average EHL film thickness. Consequently, most components operate in mixed lubrication with considerable asperity contacts, which may result in localized pressure peaks much higher than the Hertzian pressure, causing subsurface stress concentrations possibly exceeding the material yield limit. Plastic deformation, therefore, often takes place, which not only permanently changes the surface profiles and contact geometry, but alters material properties through work-hardening as well. Available mixed EHL models, however, do not consider plastic deformation, often yielding unrealistically high pressure spikes and subsurface stresses around asperity contact locations. Recently, a three-dimensional (3D) plasto-elastohydrodynamic lubrication (PEHL) model has been developed for investigating the effects of plastic deformation and material work-hardening on the EHL characteristics and subsurface stress/strain fields. The present paper is a continuation of the previous work done by Ren et al. (2010, “PEHL in point contacts,” ASME J. Tribol., 132(3), pp. 031501) that focused on model development and validation, as well as investigation of fundamental PEHL mechanisms in smooth surface contacts. This part of the study is mainly on the PEHL behavior involving simple surface irregularities, such as a single asperity or dent, which can be considered as basic elements of more complicated surface roughness. It is found that considerable plastic deformation may occur due to the pressure peaks caused by the surface irregularity, even though sometimes external loading is not heavy and the irregularity is concave. The plastic deformation may significantly affect contact and lubrication characteristics, resulting in considerable reductions in peak pressure and maximum subsurface stresses. DEWEY : 621.5 ISSN : 0742-4787 En ligne : http://scitation.aip.org/getabs/servlet/GetabsServlet?prog=normal&id=JOTRE900013 [...]