Documents disponibles écrits par cet auteur

Influence of inclination angle and machining direction on friction and transfer layer formation / Pradeep L. Menezes in Transactions of the ASME . Journal of tribology, Vol. 133 N° 1 (Janvier 2011) 

Public ISBD [article]  in Transactions of the ASME . Journal of tribology > Vol. 133 N° 1 (Janvier 2011) . - 08 p. Titre : Influence of inclination angle and machining direction on friction and transfer layer formation Type de document : texte imprimé Auteurs : Pradeep L. Menezes, Auteur ; Kishore, Auteur ; Satish V. Kailas, Auteur Année de publication : 2012 Article en page(s) : 08 p. Note générale : Tribology Langues : Anglais (eng) Mots-clés : Aluminium  alloys  Grinding  Machining  Magnesium  alloys  Plates  (structures)  Sliding  friction Index. décimale : 621.5 Energie pneumatique. Machinerie et outils. Réfrigération Résumé : In the present investigation, unidirectional grinding marks were created on a set of steel plates. Sliding experiments were then conducted with the prepared steel plates using Al–Mg alloy pins and an inclined pin-on-plate sliding tester. The goals of the experiments were to ascertain the influence of inclination angle and grinding mark direction on friction and transfer layer formation during sliding contact. The inclination angle of the plate was held at 0.2 deg, 0.6 deg, 1 deg, 1.4 deg, 1.8 deg, 2.2 deg, and 2.6 deg in the tests. The pins were slid both perpendicular and parallel to the grinding marks direction. The experiments were conducted under both dry and lubricated conditions on each plate in an ambient environment. Results showed that the coefficient of friction and the formation of transfer layer depend on the grinding marks direction and inclination angle of the hard surfaces. For a given inclination angle, under both dry and lubricated conditions, the coefficient of friction and transfer layer formation were found to be greater when the pins slid perpendicular to the unidirectional grinding marks than when the pins slid parallel to the grinding marks. In addition, a stick-slip phenomenon was observed under lubricated conditions at the highest inclination angle for sliding perpendicular to the grinding marks direction. This phenomenon could be attributed to the extent of plane strain conditions taking place at the asperity level during sliding. DEWEY : 621.5 ISSN : 0742-4787 En ligne : http://scitation.aip.org/getabs/servlet/GetabsServlet?prog=normal&id=JOTRE900013 [...] [article] Influence of inclination angle and machining direction on friction and transfer layer formation [texte imprimé] / Pradeep L. Menezes, Auteur ; Kishore, Auteur ; Satish V. Kailas, Auteur . - 2012 . - 08 p. Tribology Langues : Anglais (eng) in Transactions of the ASME . Journal of tribology > Vol. 133 N° 1 (Janvier 2011) . - 08 p. Mots-clés : Aluminium  alloys  Grinding  Machining  Magnesium  alloys  Plates  (structures)  Sliding  friction Index. décimale : 621.5 Energie pneumatique. Machinerie et outils. Réfrigération Résumé : In the present investigation, unidirectional grinding marks were created on a set of steel plates. Sliding experiments were then conducted with the prepared steel plates using Al–Mg alloy pins and an inclined pin-on-plate sliding tester. The goals of the experiments were to ascertain the influence of inclination angle and grinding mark direction on friction and transfer layer formation during sliding contact. The inclination angle of the plate was held at 0.2 deg, 0.6 deg, 1 deg, 1.4 deg, 1.8 deg, 2.2 deg, and 2.6 deg in the tests. The pins were slid both perpendicular and parallel to the grinding marks direction. The experiments were conducted under both dry and lubricated conditions on each plate in an ambient environment. Results showed that the coefficient of friction and the formation of transfer layer depend on the grinding marks direction and inclination angle of the hard surfaces. For a given inclination angle, under both dry and lubricated conditions, the coefficient of friction and transfer layer formation were found to be greater when the pins slid perpendicular to the unidirectional grinding marks than when the pins slid parallel to the grinding marks. In addition, a stick-slip phenomenon was observed under lubricated conditions at the highest inclination angle for sliding perpendicular to the grinding marks direction. This phenomenon could be attributed to the extent of plane strain conditions taking place at the asperity level during sliding. DEWEY : 621.5 ISSN : 0742-4787 En ligne : http://scitation.aip.org/getabs/servlet/GetabsServlet?prog=normal&id=JOTRE900013 [...]