Experimental study of the performance of static seals based on measurements of real contact area using thin polycarbonate films / Isami Nitta in Transactions of the ASME . Journal of tribology, Vol. 132 N° 2 (Avril 2010)  

Public ISBD [article]  inTransactions of the ASME . Journal of tribology > Vol. 132 N° 2 (Avril 2010) . - 07 p. Titre : Experimental study of the performance of static seals based on measurements of real contact area using thin polycarbonate films Type de document : texte imprimé Auteurs : Isami Nitta, Auteur ; Yoshio Matsuzaki, Auteur Année de publication : 2011 Article en page(s) : 07 p. Note générale : Tribology Langues : Anglais (eng) Mots-clés : Copper Flanges Gaskets Laminar flow Mechanical contact Plastic Polymer films Steel Turning (machining) Index. décimale : 621.5 Energie pneumatique. Machinerie et outils. Réfrigération Résumé : To clarify the sealing characteristics of metal gasket seals, leakage rates of gas and the real contact area of the seal surfaces were measured under several closing loads. The static seal consisted of a ring-shaped copper gasket and the two steel flanges that held the gasket in place. Gasket widths in the radial direction were 2 mm, 3 mm, and 5 mm. The contact surfaces of the flanges were finished by lathe turning. To determine the leakage flow paths between the gasket and the flanges, the real contact situation between them was observed using a thin polymer film 1 µm in thickness. The results indicated the leakage flow paths on the gasket surface were the radial direction perpendicular to the lathe-turned groove and the circumferential direction along the groove. As the closing loads increased, the leakage flow in the radial direction ceased and only that in the circumferential direction remained. Therefore, the cross-section of the aperture for the leakage flow in the circumferential direction was evaluated from the measured real contact area, and the leakage rates were estimated by assumption of laminar flow. The results agreed well with the measured leakage rates. DEWEY : 621.5 ISSN : 0742-4787 En ligne : http://scitation.aip.org/getabs/servlet/GetabsServlet?prog=normal&id=JOTRE900013 [...] [article] Experimental study of the performance of static seals based on measurements of real contact area using thin polycarbonate films [texte imprimé] / Isami Nitta, Auteur ; Yoshio Matsuzaki, Auteur . - 2011 . - 07 p. Tribology Langues : Anglais (eng) in Transactions of the ASME . Journal of tribology > Vol. 132 N° 2 (Avril 2010) . - 07 p. Mots-clés : Copper Flanges Gaskets Laminar flow Mechanical contact Plastic Polymer films Steel Turning (machining) Index. décimale : 621.5 Energie pneumatique. Machinerie et outils. Réfrigération Résumé : To clarify the sealing characteristics of metal gasket seals, leakage rates of gas and the real contact area of the seal surfaces were measured under several closing loads. The static seal consisted of a ring-shaped copper gasket and the two steel flanges that held the gasket in place. Gasket widths in the radial direction were 2 mm, 3 mm, and 5 mm. The contact surfaces of the flanges were finished by lathe turning. To determine the leakage flow paths between the gasket and the flanges, the real contact situation between them was observed using a thin polymer film 1 µm in thickness. The results indicated the leakage flow paths on the gasket surface were the radial direction perpendicular to the lathe-turned groove and the circumferential direction along the groove. As the closing loads increased, the leakage flow in the radial direction ceased and only that in the circumferential direction remained. Therefore, the cross-section of the aperture for the leakage flow in the circumferential direction was evaluated from the measured real contact area, and the leakage rates were estimated by assumption of laminar flow. The results agreed well with the measured leakage rates. DEWEY : 621.5 ISSN : 0742-4787 En ligne : http://scitation.aip.org/getabs/servlet/GetabsServlet?prog=normal&id=JOTRE900013 [...]

Exemplaires

Code-barres	Cote	Support	Localisation	Section	Disponibilité
aucun exemplaire