Cell structure evolution and the crystallization behavior of polypropylene / clay nanocomposites foams blown in continuous extrusion / Wentao Zhai in Industrial & engineering chemistry research, Vol. 49 N° 20 (Octobre 2010)  

Public ISBD [article]  inIndustrial & engineering chemistry research > Vol. 49 N° 20 (Octobre 2010) . - pp. 9834–9845 Titre : Cell structure evolution and the crystallization behavior of polypropylene / clay nanocomposites foams blown in continuous extrusion Type de document : texte imprimé Auteurs : Wentao Zhai, Auteur ; Takashi Kuboki, Auteur ; Lilac Wang, Auteur Année de publication : 2011 Article en page(s) : pp. 9834–9845 Note générale : Chimie industrielle Langues : Anglais (eng) Mots-clés : Crystallization Nanocomposites Résumé : In this study, linear homopolypropylene/clay (HPPC) nanocomposite foams with a high expansion ratio of about 18 and a high cell density of about 1.7 × 108 cells/cm3 were produced using an extrusion foaming method with CO2 as the physical blowing agent. The result was much better than pure HPP foams with expansion ratios of 1.7−2.2 and cell densities of 103−105 cells/cm3 obtained even at the same foaming conditions. The nanoclays had a half-exfoliated structure in the HPP matrix, and their presence dramatically affected the viscoelastic properties of HPP melt and foaming behaviors. It was found that the introduction of a small amount of nanoclay significantly increased the cell morphology of HPP foams at low die temperatures, where the cell wall was very thin and cell distribution was uniform. With an increase in nanoclay content of up to 5 wt %, cell morphology was improved gradually at broader die temperatures. Based on the cell morphology results, a suitable foaming window for clay content and die temperature was established. The mechanisms behind these phenomena are discussed from the perspective of cell nucleation and coalescence. Microstructures were found in the cell walls of HPP and HPPC nanocomposite foams, and they tended to evolve with cell wall thickness, depending on the die temperatures. Scanning electron microscopy (SEM) observation of foams and solvent-etched foams revealed that the microstructures in the cell walls were formed by covering large-sized crystals and that the absence of microstructures was due to the presence of small-sized crystals in the cell walls. A distribution of crystal sizes was observed across the foamed samples, which was affected by the die temperature and the introduction of nanoclay. The possible reasons were elaborated by considerations of temperature gradient. DSC tests indicated that the foaming process induced a low-temperature peak (Tm1) and its heat of fusion (ΔHm1) tended to evolve with the die temperature and the introduction of nanoclay. DEWEY : 660 ISSN : 0888-5885 En ligne : http://pubs.acs.org/doi/abs/10.1021/ie101225f [article] Cell structure evolution and the crystallization behavior of polypropylene / clay nanocomposites foams blown in continuous extrusion [texte imprimé] / Wentao Zhai, Auteur ; Takashi Kuboki, Auteur ; Lilac Wang, Auteur . - 2011 . - pp. 9834–9845. Chimie industrielle Langues : Anglais (eng) in Industrial & engineering chemistry research > Vol. 49 N° 20 (Octobre 2010) . - pp. 9834–9845 Mots-clés : Crystallization Nanocomposites Résumé : In this study, linear homopolypropylene/clay (HPPC) nanocomposite foams with a high expansion ratio of about 18 and a high cell density of about 1.7 × 108 cells/cm3 were produced using an extrusion foaming method with CO2 as the physical blowing agent. The result was much better than pure HPP foams with expansion ratios of 1.7−2.2 and cell densities of 103−105 cells/cm3 obtained even at the same foaming conditions. The nanoclays had a half-exfoliated structure in the HPP matrix, and their presence dramatically affected the viscoelastic properties of HPP melt and foaming behaviors. It was found that the introduction of a small amount of nanoclay significantly increased the cell morphology of HPP foams at low die temperatures, where the cell wall was very thin and cell distribution was uniform. With an increase in nanoclay content of up to 5 wt %, cell morphology was improved gradually at broader die temperatures. Based on the cell morphology results, a suitable foaming window for clay content and die temperature was established. The mechanisms behind these phenomena are discussed from the perspective of cell nucleation and coalescence. Microstructures were found in the cell walls of HPP and HPPC nanocomposite foams, and they tended to evolve with cell wall thickness, depending on the die temperatures. Scanning electron microscopy (SEM) observation of foams and solvent-etched foams revealed that the microstructures in the cell walls were formed by covering large-sized crystals and that the absence of microstructures was due to the presence of small-sized crystals in the cell walls. A distribution of crystal sizes was observed across the foamed samples, which was affected by the die temperature and the introduction of nanoclay. The possible reasons were elaborated by considerations of temperature gradient. DSC tests indicated that the foaming process induced a low-temperature peak (Tm1) and its heat of fusion (ΔHm1) tended to evolve with the die temperature and the introduction of nanoclay. DEWEY : 660 ISSN : 0888-5885 En ligne : http://pubs.acs.org/doi/abs/10.1021/ie101225f

Exemplaires

Code-barres	Cote	Support	Localisation	Section	Disponibilité
aucun exemplaire