Documents disponibles écrits par cet auteur

Design parameters for an aircraft engine exit plane particle sampling system / Hsi-Wu Wong in Transactions of the ASME . Journal of engineering for gas turbines and power, Vol. 133 N° 2 (Fevrier 2011) 

Public ISBD [article]  in Transactions of the ASME . Journal of engineering for gas turbines and power > Vol. 133 N° 2 (Fevrier 2011) . - 15 p. Titre : Design parameters for an aircraft engine exit plane particle sampling system Type de document : texte imprimé Auteurs : Hsi-Wu Wong, Auteur ; Zhenhong Yu, Auteur ; Michael T. Timko, Auteur Année de publication : 2012 Article en page(s) : 15 p. Note générale : Génie Mécanique Langues : Anglais (eng) Mots-clés : Aerospace  engines  Air  pollution  measurement  Design  engineering  Gas  turbines Index. décimale : 620.1 Essais des matériaux. Défauts des matériaux. Protection des matériaux Résumé : The experimental data and numerical modeling were utilized to investigate the effects of exhaust sampling parameters on the measurements of particulate matter (PM) emitted at the exit plane of gas-turbine engines. The results provide guidance for sampling system design and operation. Engine power level is the most critical factor that influences the size and quantity of black carbon soot particles emitted from gas-turbine engines and must be considered in sampling system design. The results of this investigation indicate that the available soot surface area significantly affects the amount of volatile gases that can condense onto soot particles. During exhaust particle measurements, a dilution gas is typically added to the sampled exhaust stream to suppress volatile particle formation in the sampling line. Modeling results indicate that the dilution gas should be introduced upstream before a critical location in the sampling line that corresponds to the onset of particle formation microphysics. Also, the dilution gas should be dry for maximum nucleation suppression. In most aircraft PM emissions measurements, the probe-rake systems are water cooled and the sampling line may be heated. Modeling results suggest that the water cooling of the probe tip should be limited to avoid overcooling the sampling line wall temperature and, thus, minimize additional particle formation in the sampling line. The experimental data show that heating the sampling lines will decrease black carbon and sulfate PM mass and increase organic PM mass reaching the instruments. Sampling line transmission losses may prevent some of the particles emitted at the engine exit plane from reaching the instruments, especially particles that are smaller in size. Modeling results suggest that homogeneous nucleation can occur in the engine exit plane sampling line. If newly nucleated particles, typically smaller than 10 nm, are indeed formed in the sampling line, sampling line particle losses provide a possible explanation, in addition to the application of dry diluent, that they are generally not observed in the PM emissions measurements. DEWEY : 620.1 ISSN : 0742-4795 En ligne : http://scitation.aip.org/getabs/servlet/GetabsServlet?prog=normal&id=JETPEZ00013 [...] [article] Design parameters for an aircraft engine exit plane particle sampling system [texte imprimé] / Hsi-Wu Wong, Auteur ; Zhenhong Yu, Auteur ; Michael T. Timko, Auteur . - 2012 . - 15 p. Génie Mécanique Langues : Anglais (eng) in Transactions of the ASME . Journal of engineering for gas turbines and power > Vol. 133 N° 2 (Fevrier 2011) . - 15 p. Mots-clés : Aerospace  engines  Air  pollution  measurement  Design  engineering  Gas  turbines Index. décimale : 620.1 Essais des matériaux. Défauts des matériaux. Protection des matériaux Résumé : The experimental data and numerical modeling were utilized to investigate the effects of exhaust sampling parameters on the measurements of particulate matter (PM) emitted at the exit plane of gas-turbine engines. The results provide guidance for sampling system design and operation. Engine power level is the most critical factor that influences the size and quantity of black carbon soot particles emitted from gas-turbine engines and must be considered in sampling system design. The results of this investigation indicate that the available soot surface area significantly affects the amount of volatile gases that can condense onto soot particles. During exhaust particle measurements, a dilution gas is typically added to the sampled exhaust stream to suppress volatile particle formation in the sampling line. Modeling results indicate that the dilution gas should be introduced upstream before a critical location in the sampling line that corresponds to the onset of particle formation microphysics. Also, the dilution gas should be dry for maximum nucleation suppression. In most aircraft PM emissions measurements, the probe-rake systems are water cooled and the sampling line may be heated. Modeling results suggest that the water cooling of the probe tip should be limited to avoid overcooling the sampling line wall temperature and, thus, minimize additional particle formation in the sampling line. The experimental data show that heating the sampling lines will decrease black carbon and sulfate PM mass and increase organic PM mass reaching the instruments. Sampling line transmission losses may prevent some of the particles emitted at the engine exit plane from reaching the instruments, especially particles that are smaller in size. Modeling results suggest that homogeneous nucleation can occur in the engine exit plane sampling line. If newly nucleated particles, typically smaller than 10 nm, are indeed formed in the sampling line, sampling line particle losses provide a possible explanation, in addition to the application of dry diluent, that they are generally not observed in the PM emissions measurements. DEWEY : 620.1 ISSN : 0742-4795 En ligne : http://scitation.aip.org/getabs/servlet/GetabsServlet?prog=normal&id=JETPEZ00013 [...]

Gas turbine engine emissions—Part I: Volatile organic compounds and nitrogen oxides / Michael T. Timko in Transactions of the ASME . Journal of engineering for gas turbines and power, Vol. 132 N° 6 (Juin 2010) 

Public ISBD [article]  in Transactions of the ASME . Journal of engineering for gas turbines and power > Vol. 132 N° 6 (Juin 2010) . - 14 p. Titre : Gas turbine engine emissions—Part I: Volatile organic compounds and nitrogen oxides Type de document : texte imprimé Auteurs : Michael T. Timko, Auteur ; Scott C. Herndon, Auteur ; Ezra C. Wood, Auteur Année de publication : 2011 Article en page(s) : 14 p. Note générale : Génie Mécanique Langues : Anglais (eng) Mots-clés : Aerospace  engines  Aircraft  Gas  turbines  Organic  compounds Index. décimale : 620.1 Essais des matériaux. Défauts des matériaux. Protection des matériaux Résumé : The potential human health and environmental impacts of aircraft gas turbine engine emissions during normal airport operation are issues of growing concern. During the JETS/Aircraft Particle Emissions eXperiment(APEX)-2 and APEX-3 field campaigns, we performed an extensive series of gas phase and particulate emissions measurements of on-wing gas turbine engines. In all, nine different CFM56 style engines (including both CFM56-3B1 and -7B22 models) and seven additional engines (two RB211-535E4-B engines, three AE3007 engines, one PW4158, and one CJ6108A) were studied to evaluate engine-to-engine variability. Specific gas-phase measurements include NO2, NO, and total NOx, HCHO, C2H4, CO, and a range of volatile organic compounds (e.g., benzene, styrene, toluene, naphthalene). A number of broad conclusions can be made based on the gas-phase data set: (1) field measurements of gas-phase emission indices (EIs) are generally consistent with ICAO certification values; (2) speciation of gas phase NOx between NO and NO2 is reproducible for different engine types and favors NO2 at low power (and low fuel flow rate) and NO at high power (high fuel flow rate); (3) emission indices of gas-phase organic compounds and CO decrease rapidly with increasing fuel flow rate; (4) plotting EI-CO or volatile organic compound EIs against fuel flow rate collapses much of the variability between the different engines, with one exception (AE3007); (5) HCHO, ethylene, acetaldehyde, and propene are the most abundant volatile organic compounds present in the exhaust gases that we can detect, independent of engine technology differences. Empirical correlations accurate to within 30% and based on the publicly available engine parameters are presented for estimating EI-NOx and EI-NO2. Engine-to-engine variability, unavailability of combustor input conditions, changing ambient temperatures, and complex reaction dynamics limit the accuracy of global correlations for CO or volatile organic compound EIs. DEWEY : 620.1 ISSN : 0742-4795 En ligne : http://asmedl.org/getabs/servlet/GetabsServlet?prog=normal&id=JETPEZ000132000006 [...] [article] Gas turbine engine emissions—Part I: Volatile organic compounds and nitrogen oxides [texte imprimé] / Michael T. Timko, Auteur ; Scott C. Herndon, Auteur ; Ezra C. Wood, Auteur . - 2011 . - 14 p. Génie Mécanique Langues : Anglais (eng) in Transactions of the ASME . Journal of engineering for gas turbines and power > Vol. 132 N° 6 (Juin 2010) . - 14 p. Mots-clés : Aerospace  engines  Aircraft  Gas  turbines  Organic  compounds Index. décimale : 620.1 Essais des matériaux. Défauts des matériaux. Protection des matériaux Résumé : The potential human health and environmental impacts of aircraft gas turbine engine emissions during normal airport operation are issues of growing concern. During the JETS/Aircraft Particle Emissions eXperiment(APEX)-2 and APEX-3 field campaigns, we performed an extensive series of gas phase and particulate emissions measurements of on-wing gas turbine engines. In all, nine different CFM56 style engines (including both CFM56-3B1 and -7B22 models) and seven additional engines (two RB211-535E4-B engines, three AE3007 engines, one PW4158, and one CJ6108A) were studied to evaluate engine-to-engine variability. Specific gas-phase measurements include NO2, NO, and total NOx, HCHO, C2H4, CO, and a range of volatile organic compounds (e.g., benzene, styrene, toluene, naphthalene). A number of broad conclusions can be made based on the gas-phase data set: (1) field measurements of gas-phase emission indices (EIs) are generally consistent with ICAO certification values; (2) speciation of gas phase NOx between NO and NO2 is reproducible for different engine types and favors NO2 at low power (and low fuel flow rate) and NO at high power (high fuel flow rate); (3) emission indices of gas-phase organic compounds and CO decrease rapidly with increasing fuel flow rate; (4) plotting EI-CO or volatile organic compound EIs against fuel flow rate collapses much of the variability between the different engines, with one exception (AE3007); (5) HCHO, ethylene, acetaldehyde, and propene are the most abundant volatile organic compounds present in the exhaust gases that we can detect, independent of engine technology differences. Empirical correlations accurate to within 30% and based on the publicly available engine parameters are presented for estimating EI-NOx and EI-NO2. Engine-to-engine variability, unavailability of combustor input conditions, changing ambient temperatures, and complex reaction dynamics limit the accuracy of global correlations for CO or volatile organic compound EIs. DEWEY : 620.1 ISSN : 0742-4795 En ligne : http://asmedl.org/getabs/servlet/GetabsServlet?prog=normal&id=JETPEZ000132000006 [...]

Gas turbine engine emissions—Part II: Chemical properties of particulate matter / Michael T. Timko in Transactions of the ASME . Journal of engineering for gas turbines and power, Vol. 132 N° 6 (Juin 2010) 

Public ISBD [article]  in Transactions of the ASME . Journal of engineering for gas turbines and power > Vol. 132 N° 6 (Juin 2010) . - 15 p. Titre : Gas turbine engine emissions—Part II: Chemical properties of particulate matter Type de document : texte imprimé Auteurs : Michael T. Timko, Auteur ; Timothy B. Onasch, Auteur ; Megan J. Northway, Auteur Année de publication : 2011 Article en page(s) : 15 p. Note générale : Génie Mécanique Langues : Anglais (eng) Mots-clés : Aerospace  engines  Cooling  Gas  turbines Index. décimale : 620.1 Essais des matériaux. Défauts des matériaux. Protection des matériaux Résumé : The characterization of volatile and nonvolatile particle materials present in gas turbine exhaust is critical for accurate estimation of the potential impacts of airport activities on local air quality, atmospheric processes, and climate change. Two field campaigns were performed to collect an extensive set of particle and gaseous emission data for on-wing gas turbine engines. The tests included CFM56, RB211-535E4-B, AE3007, PW4158, and CJ610 engines, providing the opportunity to compare emissions from a wide range of engine technologies. Here we report mass, number, composition, and size data for the nonvolatile (soot) and volatile particles present in engine exhaust. For all engines, soot emissions (EIm-soot) are greater at climbout (85% power) and takeoff (100%) power than idle (4% or 7%) and approach (30%). At the engine exit plane, soot is the only type of particle detected. For exhaust sampled downwind (15–50 m) and diluted by ambient air, total particle number emissions (EIn-total) increases by about one or two orders of magnitude relative to the engine exit plane, and the increase is driven by volatile particles that have freshly nucleated in the cooling exhaust gas both in the free atmosphere and in the extractive sample lines. Fuel sulfur content is the determining factor for nucleation of new particles in the cooling exhaust gases. Compositional analysis indicates that the volatile particles consist of sulfate and organic materials (EIm-sulfate and EIm-organic). We estimate a lower bound S[IV] to S[VI] conversion efficiency of (0.08±0.01)%, independent of engine technology. Measurements of EIm-organic ranged from about 0.1 mg kg−1 to 40 mg kg−1. Lubrication oil was present in particles emitted by all engines and accounted for over 90% of the particulate organic mass under some conditions. The products of incomplete combustion are a likely source of the remaining volatile organic particle material. DEWEY : 620.1 ISSN : 0742-4795 En ligne : http://asmedl.org/getabs/servlet/GetabsServlet?prog=normal&id=JETPEZ000132000006 [...] [article] Gas turbine engine emissions—Part II: Chemical properties of particulate matter [texte imprimé] / Michael T. Timko, Auteur ; Timothy B. Onasch, Auteur ; Megan J. Northway, Auteur . - 2011 . - 15 p. Génie Mécanique Langues : Anglais (eng) in Transactions of the ASME . Journal of engineering for gas turbines and power > Vol. 132 N° 6 (Juin 2010) . - 15 p. Mots-clés : Aerospace  engines  Cooling  Gas  turbines Index. décimale : 620.1 Essais des matériaux. Défauts des matériaux. Protection des matériaux Résumé : The characterization of volatile and nonvolatile particle materials present in gas turbine exhaust is critical for accurate estimation of the potential impacts of airport activities on local air quality, atmospheric processes, and climate change. Two field campaigns were performed to collect an extensive set of particle and gaseous emission data for on-wing gas turbine engines. The tests included CFM56, RB211-535E4-B, AE3007, PW4158, and CJ610 engines, providing the opportunity to compare emissions from a wide range of engine technologies. Here we report mass, number, composition, and size data for the nonvolatile (soot) and volatile particles present in engine exhaust. For all engines, soot emissions (EIm-soot) are greater at climbout (85% power) and takeoff (100%) power than idle (4% or 7%) and approach (30%). At the engine exit plane, soot is the only type of particle detected. For exhaust sampled downwind (15–50 m) and diluted by ambient air, total particle number emissions (EIn-total) increases by about one or two orders of magnitude relative to the engine exit plane, and the increase is driven by volatile particles that have freshly nucleated in the cooling exhaust gas both in the free atmosphere and in the extractive sample lines. Fuel sulfur content is the determining factor for nucleation of new particles in the cooling exhaust gases. Compositional analysis indicates that the volatile particles consist of sulfate and organic materials (EIm-sulfate and EIm-organic). We estimate a lower bound S[IV] to S[VI] conversion efficiency of (0.08±0.01)%, independent of engine technology. Measurements of EIm-organic ranged from about 0.1 mg kg−1 to 40 mg kg−1. Lubrication oil was present in particles emitted by all engines and accounted for over 90% of the particulate organic mass under some conditions. The products of incomplete combustion are a likely source of the remaining volatile organic particle material. DEWEY : 620.1 ISSN : 0742-4795 En ligne : http://asmedl.org/getabs/servlet/GetabsServlet?prog=normal&id=JETPEZ000132000006 [...]

Measurement of volatile particulate matter emissions from aircraft engines using a simulated plume aging system / Peck, Jay in Transactions of the ASME . Journal of engineering for gas turbines and power, Vol. 134 N° 6 (Juin 2012) 

Public ISBD [article]  in Transactions of the ASME . Journal of engineering for gas turbines and power > Vol. 134 N° 6 (Juin 2012) . - 08 p. Titre : Measurement of volatile particulate matter emissions from aircraft engines using a simulated plume aging system Type de document : texte imprimé Auteurs : Peck, Jay, Auteur ; Michael T. Timko, Auteur ; Zhenhong Yu, Auteur Année de publication : 2012 Article en page(s) : 08 p. Note générale : Génie mécanique Langues : Anglais (eng) Mots-clés : Volatile  particulate  matter  emissions  Aircraft  engines  Plume  aging  system Index. décimale : 620.1 Essais des matériaux. Défauts des matériaux. Protection des matériaux Résumé : Aircraft exhaust contains nonvolatile (soot) particulate matter (PM), trace gas pollutants, and volatile PM precursor material. Nonvolatile soot particles are predominantly present at the engine exit plane, but volatile PM precursors form new particles or add mass to the existing ones as the exhaust is diluted and cooled. Accurately characterizing the volatile PM mass, number, and size distribution is challenging due to this evolving nature and the impact of local ambient conditions on the gas-to-particle conversion processes. To accurately and consistently measure the aircraft PM emissions, a dilution and aging sampling system that can condense volatile precursors to particle phase to simulate the atmospheric evolution of aircraft engine exhaust has been developed. In this paper, a field demonstration of its operation is described. The dilution/aging probe system was tested using both a combustor rig and on-wing CFM56-7 engines. During the combustor rig testing at NASA Glenn Research Center, the dilution/aging probe supported formation of both nucleation/growth mode particles and soot coatings. The results showed that by increasing residence time, the nucleation particles become larger in size, increase in total mass, and decrease in number. During the on-wing CFM56-7 engine testing at Chicago Midway Airport, the dilution/aging probe was able to form soot coatings along with nucleation mode particles, unlike conventional 1-m probe engine measurements. The number concentration of nucleation particles depended on the sample fraction and relative humidity of the dilution air. The performance of the instrument is analyzed and explained using computational microphysics simulations. DEWEY : 620.1 ISSN : 0742-4795 En ligne : http://asmedl.org/getabs/servlet/GetabsServlet?prog=normal&id=JETPEZ000134000006 [...] [article] Measurement of volatile particulate matter emissions from aircraft engines using a simulated plume aging system [texte imprimé] / Peck, Jay, Auteur ; Michael T. Timko, Auteur ; Zhenhong Yu, Auteur . - 2012 . - 08 p. Génie mécanique Langues : Anglais (eng) in Transactions of the ASME . Journal of engineering for gas turbines and power > Vol. 134 N° 6 (Juin 2012) . - 08 p. Mots-clés : Volatile  particulate  matter  emissions  Aircraft  engines  Plume  aging  system Index. décimale : 620.1 Essais des matériaux. Défauts des matériaux. Protection des matériaux Résumé : Aircraft exhaust contains nonvolatile (soot) particulate matter (PM), trace gas pollutants, and volatile PM precursor material. Nonvolatile soot particles are predominantly present at the engine exit plane, but volatile PM precursors form new particles or add mass to the existing ones as the exhaust is diluted and cooled. Accurately characterizing the volatile PM mass, number, and size distribution is challenging due to this evolving nature and the impact of local ambient conditions on the gas-to-particle conversion processes. To accurately and consistently measure the aircraft PM emissions, a dilution and aging sampling system that can condense volatile precursors to particle phase to simulate the atmospheric evolution of aircraft engine exhaust has been developed. In this paper, a field demonstration of its operation is described. The dilution/aging probe system was tested using both a combustor rig and on-wing CFM56-7 engines. During the combustor rig testing at NASA Glenn Research Center, the dilution/aging probe supported formation of both nucleation/growth mode particles and soot coatings. The results showed that by increasing residence time, the nucleation particles become larger in size, increase in total mass, and decrease in number. During the on-wing CFM56-7 engine testing at Chicago Midway Airport, the dilution/aging probe was able to form soot coatings along with nucleation mode particles, unlike conventional 1-m probe engine measurements. The number concentration of nucleation particles depended on the sample fraction and relative humidity of the dilution air. The performance of the instrument is analyzed and explained using computational microphysics simulations. DEWEY : 620.1 ISSN : 0742-4795 En ligne : http://asmedl.org/getabs/servlet/GetabsServlet?prog=normal&id=JETPEZ000134000006 [...]