Documents disponibles écrits par cet auteur

Flow and mass transfer in bends under flow-accelerated corrosion wall thinning conditions / John M. Pietralik in Transactions of the ASME . Journal of engineering for gas turbines and power, Vol. 133 N° 1 (Janvier 2011) 

Public ISBD [article]  in Transactions of the ASME . Journal of engineering for gas turbines and power > Vol. 133 N° 1 (Janvier 2011) . - 07 p. Titre : Flow and mass transfer in bends under flow-accelerated corrosion wall thinning conditions Type de document : texte imprimé Auteurs : John M. Pietralik, Auteur ; Chris S. Schefski, Auteur Année de publication : 2012 Article en page(s) : 07 p. Note générale : Génie Mécanique Langues : Anglais (eng) Mots-clés : Boilers  Corrosion  Fluid  dynamics  Heat  exchangers  Heat  transfer  Mass  transfer  Nuclear  reactor  steam  generators  Surface  roughness Index. décimale : 620.1 Essais des matériaux. Défauts des matériaux. Protection des matériaux Résumé : The three groups of parameters that affect flow-accelerated corrosion (FAC) are the flow conditions, water chemistry, and materials. Nuclear power plant (NPP) data and laboratory tests confirm that, under alkaline water chemistry, there is a close relationship between local flow conditions and FAC rates in the piping components. The knowledge of the local flow effects can be useful for developing targeted inspection plans for piping components and predicting the location of the highest FAC rate for a given piping component. A similar evaluation applies also to the FAC in heat transfer equipments such as heat exchangers and steam generators. The objective of this paper is to examine the role of the flow and mass transfer in bends under alkaline FAC conditions. Bends experience increased FAC rates compared with straight pipes, and are the most common components in piping systems. This study presents numerical simulations of the mass transfer of ferrous ions and experimental results of the FAC rate in bends. It also shows correlations for mass transfer coefficients in bends and reviews the most important flow parameters affecting the mass transfer coefficient. The role of bend geometry and, in particular, the short and long radii, surface roughness, wall shear stress, and local turbulence, is discussed. Computational fluid dynamics calculations and plant artifact measurements for short- and long-radius bends are presented. The effect of the close proximity of the two bends on the FAC rate is also examined based on CANDU (CANDU is a registered trademark of the Atomic Energy of Canada Limited) NPP inspection data and compared with literature data. DEWEY : 620.1 ISSN : 0742-4795 En ligne : http://scitation.aip.org/getabs/servlet/GetabsServlet?prog=normal&id=JETPEZ00013 [...] [article] Flow and mass transfer in bends under flow-accelerated corrosion wall thinning conditions [texte imprimé] / John M. Pietralik, Auteur ; Chris S. Schefski, Auteur . - 2012 . - 07 p. Génie Mécanique Langues : Anglais (eng) in Transactions of the ASME . Journal of engineering for gas turbines and power > Vol. 133 N° 1 (Janvier 2011) . - 07 p. Mots-clés : Boilers  Corrosion  Fluid  dynamics  Heat  exchangers  Heat  transfer  Mass  transfer  Nuclear  reactor  steam  generators  Surface  roughness Index. décimale : 620.1 Essais des matériaux. Défauts des matériaux. Protection des matériaux Résumé : The three groups of parameters that affect flow-accelerated corrosion (FAC) are the flow conditions, water chemistry, and materials. Nuclear power plant (NPP) data and laboratory tests confirm that, under alkaline water chemistry, there is a close relationship between local flow conditions and FAC rates in the piping components. The knowledge of the local flow effects can be useful for developing targeted inspection plans for piping components and predicting the location of the highest FAC rate for a given piping component. A similar evaluation applies also to the FAC in heat transfer equipments such as heat exchangers and steam generators. The objective of this paper is to examine the role of the flow and mass transfer in bends under alkaline FAC conditions. Bends experience increased FAC rates compared with straight pipes, and are the most common components in piping systems. This study presents numerical simulations of the mass transfer of ferrous ions and experimental results of the FAC rate in bends. It also shows correlations for mass transfer coefficients in bends and reviews the most important flow parameters affecting the mass transfer coefficient. The role of bend geometry and, in particular, the short and long radii, surface roughness, wall shear stress, and local turbulence, is discussed. Computational fluid dynamics calculations and plant artifact measurements for short- and long-radius bends are presented. The effect of the close proximity of the two bends on the FAC rate is also examined based on CANDU (CANDU is a registered trademark of the Atomic Energy of Canada Limited) NPP inspection data and compared with literature data. DEWEY : 620.1 ISSN : 0742-4795 En ligne : http://scitation.aip.org/getabs/servlet/GetabsServlet?prog=normal&id=JETPEZ00013 [...]