Tri-axial force measurements on the cylinder of a motored SI engine operated on lubricants of differing viscosity / Bryan O'Rourke in Transactions of the ASME . Journal of engineering for gas turbines and power, Vol. 132 N° 9 (Septembre 2010)  

Public ISBD [article]  inTransactions of the ASME . Journal of engineering for gas turbines and power > Vol. 132 N° 9 (Septembre 2010) . - 07 p. Titre : Tri-axial force measurements on the cylinder of a motored SI engine operated on lubricants of differing viscosity Type de document : texte imprimé Auteurs : Bryan O'Rourke, Auteur ; Donald Radford, Auteur ; Rudolf Stanglmaier, Auteur Année de publication : 2011 Article en page(s) : 07 p. Note générale : Génie Mécanique Langues : Anglais (eng) Mots-clés : Force measurement Friction Internal combustion engines Lubricants Lubrication Viscosity Index. décimale : 620.1 Essais des matériaux. Défauts des matériaux. Protection des matériaux Résumé : Friction is a determining factor in the efficiency and performance of internal combustion engines. Losses in the form of friction work typically account for 10–20% of an engine's output. Improvements in the friction characteristics of the power cylinder assembly are essential for reducing total engine friction and improving the mechanical efficiency of internal combustion engines. This paper describes the development and implementation of a new concept of the “floating liner” engine at Colorado State University that allows 0.5 crank angle deg resolved measurement of the forces on the cylinder along three axes—in the axial direction, the thrust direction, and along the wrist pin. Three different lubricants with differing properties were tested to observe the friction characteristics of each. The experimental results showed that the floating liner engine was able to resolve changes in friction characteristics coinciding with changes in lubricant viscosity and temperature. The axial force increases at TDC and BDC were observed as lubricant viscosity was decreased and larger amounts of mixed and boundary lubrication began to occur. For each test the axial friction force data was used to calculate total cycle friction work. The thrust and off-axis (wrist pin direction) forces are discussed under the same circumstances. DEWEY : 620.1 ISSN : 0742-4795 En ligne : http://scitation.aip.org/getabs/servlet/GetabsServlet?prog=normal&id=JETPEZ00013 [...] [article] Tri-axial force measurements on the cylinder of a motored SI engine operated on lubricants of differing viscosity [texte imprimé] / Bryan O'Rourke, Auteur ; Donald Radford, Auteur ; Rudolf Stanglmaier, Auteur . - 2011 . - 07 p. Génie Mécanique Langues : Anglais (eng) in Transactions of the ASME . Journal of engineering for gas turbines and power > Vol. 132 N° 9 (Septembre 2010) . - 07 p. Mots-clés : Force measurement Friction Internal combustion engines Lubricants Lubrication Viscosity Index. décimale : 620.1 Essais des matériaux. Défauts des matériaux. Protection des matériaux Résumé : Friction is a determining factor in the efficiency and performance of internal combustion engines. Losses in the form of friction work typically account for 10–20% of an engine's output. Improvements in the friction characteristics of the power cylinder assembly are essential for reducing total engine friction and improving the mechanical efficiency of internal combustion engines. This paper describes the development and implementation of a new concept of the “floating liner” engine at Colorado State University that allows 0.5 crank angle deg resolved measurement of the forces on the cylinder along three axes—in the axial direction, the thrust direction, and along the wrist pin. Three different lubricants with differing properties were tested to observe the friction characteristics of each. The experimental results showed that the floating liner engine was able to resolve changes in friction characteristics coinciding with changes in lubricant viscosity and temperature. The axial force increases at TDC and BDC were observed as lubricant viscosity was decreased and larger amounts of mixed and boundary lubrication began to occur. For each test the axial friction force data was used to calculate total cycle friction work. The thrust and off-axis (wrist pin direction) forces are discussed under the same circumstances. DEWEY : 620.1 ISSN : 0742-4795 En ligne : http://scitation.aip.org/getabs/servlet/GetabsServlet?prog=normal&id=JETPEZ00013 [...]

Exemplaires

Code-barres	Cote	Support	Localisation	Section	Disponibilité
aucun exemplaire