Documents disponibles écrits par cet auteur

Combining instantaneous temperature measurements and CFD for analysis of fuel impingement on the DISI engine piston top / Kukwon Cho in Transactions of the ASME . Journal of engineering for gas turbines and power, Vol. 132 N° 7 (Juillet 2010) 

Public ISBD [article]  in Transactions of the ASME . Journal of engineering for gas turbines and power > Vol. 132 N° 7 (Juillet 2010) . - 09 p. Titre : Combining instantaneous temperature measurements and CFD for analysis of fuel impingement on the DISI engine piston top Type de document : texte imprimé Auteurs : Kukwon Cho, Auteur ; Ronald O. Grover, Jr., Auteur ; Dennis Assanis, Auteur Année de publication : 2011 Article en page(s) : 09 p. Note générale : Génie Mécanique Langues : Anglais (eng) Mots-clés : Computational  fluid  dynamics  Heat  measurement  Pistons  Thermocouples Index. décimale : 620.1 Essais des matériaux. Défauts des matériaux. Protection des matériaux Résumé : A two-pronged experimental and computational study was conducted to explore the formation, transport, and vaporization of a wall film located at the piston surface within a four-valve, pent-roof, direct-injection spark-ignition engine, with the fuel injector located between the two intake valves. Negative temperature swings were observed at three piston locations during early injection, thus confirming the ability of fast-response thermocouples to capture the effects of impingement and heat loss associated with fuel film evaporation. Computational fluid dynamics (CFD) simulation results indicated that the fuel film evaporation process is extremely fast under conditions present during intake. Hence, the heat loss measured on the surface can be directly tied to the heating of the fuel film and its complete evaporation, with the wetted area estimated based on CFD predictions. This finding is critical for estimating the local fuel film thickness from measured heat loss. The simulated fuel film thickness and transport corroborated well temporally and spatially with measurements at thermocouple locations directly in the path of the spray, thus validating the spray and impingement models. Under the strategies tested, up to 23% of fuel injected impinges upon the piston and creates a fuel film with thickness of up to 1.2 µm. In summary, the study demonstrates the usefulness of heat flux measurements to quantitatively characterize the fuel film on the piston top and allows for validation of the CFD code. DEWEY : 620.1 ISSN : 0742-4795 En ligne : http://asmedl.org/getabs/servlet/GetabsServlet?prog=normal&id=JETPEZ000132000007 [...] [article] Combining instantaneous temperature measurements and CFD for analysis of fuel impingement on the DISI engine piston top [texte imprimé] / Kukwon Cho, Auteur ; Ronald O. Grover, Jr., Auteur ; Dennis Assanis, Auteur . - 2011 . - 09 p. Génie Mécanique Langues : Anglais (eng) in Transactions of the ASME . Journal of engineering for gas turbines and power > Vol. 132 N° 7 (Juillet 2010) . - 09 p. Mots-clés : Computational  fluid  dynamics  Heat  measurement  Pistons  Thermocouples Index. décimale : 620.1 Essais des matériaux. Défauts des matériaux. Protection des matériaux Résumé : A two-pronged experimental and computational study was conducted to explore the formation, transport, and vaporization of a wall film located at the piston surface within a four-valve, pent-roof, direct-injection spark-ignition engine, with the fuel injector located between the two intake valves. Negative temperature swings were observed at three piston locations during early injection, thus confirming the ability of fast-response thermocouples to capture the effects of impingement and heat loss associated with fuel film evaporation. Computational fluid dynamics (CFD) simulation results indicated that the fuel film evaporation process is extremely fast under conditions present during intake. Hence, the heat loss measured on the surface can be directly tied to the heating of the fuel film and its complete evaporation, with the wetted area estimated based on CFD predictions. This finding is critical for estimating the local fuel film thickness from measured heat loss. The simulated fuel film thickness and transport corroborated well temporally and spatially with measurements at thermocouple locations directly in the path of the spray, thus validating the spray and impingement models. Under the strategies tested, up to 23% of fuel injected impinges upon the piston and creates a fuel film with thickness of up to 1.2 µm. In summary, the study demonstrates the usefulness of heat flux measurements to quantitatively characterize the fuel film on the piston top and allows for validation of the CFD code. DEWEY : 620.1 ISSN : 0742-4795 En ligne : http://asmedl.org/getabs/servlet/GetabsServlet?prog=normal&id=JETPEZ000132000007 [...]

The effect of intake valve deactivation on lean stratified charge combustion at an idling condition of a spark ignition direct injection engine / Ronald O. Grover, Jr. in Transactions of the ASME . Journal of engineering for gas turbines and power, Vol. 134 N° 9 (Septembre 2012) 

Public ISBD [article]  in Transactions of the ASME . Journal of engineering for gas turbines and power > Vol. 134 N° 9 (Septembre 2012) . - 11 p. Titre : The effect of intake valve deactivation on lean stratified charge combustion at an idling condition of a spark ignition direct injection engine Type de document : texte imprimé Auteurs : Ronald O. Grover, Jr., Auteur ; Junseok Chang, Auteur ; Edward R. Masters, Auteur Année de publication : 2012 Article en page(s) : 11 p. Note générale : Génie mécanique Langues : Anglais (eng) Mots-clés : Intake  valve  deactivation  Spark  ignition  direct  injection  (SIDI)  Computational  fluid  dynamics  (CFD) Index. décimale : 620.1 Essais des matériaux. Défauts des matériaux. Protection des matériaux Résumé : A combined experimental and analytical study was carried out to understand the improvement in combustion performance of a four-valve spark ignition direct injection (SIDI) wall-guided engine operating at lean, stratified idle with enhanced in-cylinder charge motion by deactivating one of the two intake valves. A fully warmed-up engine was operated at low speed, light load by injecting the fuel from a pressure-swirl injector during the compression stroke to produce a stratified fuel cloud surrounding the spark plug at the time of ignition. Steady state flow-bench measurements and computational fluid dynamics (CFD) calculations showed that valve deactivation primarily increased the in-cylinder swirl intensity as compared with opening both intake valves. Engine dynamometer measurements showed an increase in charge motion led to improved combustion stability, increased combustion efficiency, lower fuel consumption, and higher dilution tolerance. A CFD study was conducted using in-house models of spray and combustion to simulate the engine operating with and without valve deactivation. The computations demonstrated that the improved combustion was primarily driven by higher laminar flame speeds through enhanced mixing of internal residual gases, better containment of the fuel cloud within the piston bowl, and higher postflame diffusion burn rates during the initial, main, and late stages of the combustion process, respectively. DEWEY : 620.1 ISSN : 0742-4795 En ligne : http://asmedl.org/getabs/servlet/GetabsServlet?prog=normal&id=JETPEZ000134000009 [...] [article] The effect of intake valve deactivation on lean stratified charge combustion at an idling condition of a spark ignition direct injection engine [texte imprimé] / Ronald O. Grover, Jr., Auteur ; Junseok Chang, Auteur ; Edward R. Masters, Auteur . - 2012 . - 11 p. Génie mécanique Langues : Anglais (eng) in Transactions of the ASME . Journal of engineering for gas turbines and power > Vol. 134 N° 9 (Septembre 2012) . - 11 p. Mots-clés : Intake  valve  deactivation  Spark  ignition  direct  injection  (SIDI)  Computational  fluid  dynamics  (CFD) Index. décimale : 620.1 Essais des matériaux. Défauts des matériaux. Protection des matériaux Résumé : A combined experimental and analytical study was carried out to understand the improvement in combustion performance of a four-valve spark ignition direct injection (SIDI) wall-guided engine operating at lean, stratified idle with enhanced in-cylinder charge motion by deactivating one of the two intake valves. A fully warmed-up engine was operated at low speed, light load by injecting the fuel from a pressure-swirl injector during the compression stroke to produce a stratified fuel cloud surrounding the spark plug at the time of ignition. Steady state flow-bench measurements and computational fluid dynamics (CFD) calculations showed that valve deactivation primarily increased the in-cylinder swirl intensity as compared with opening both intake valves. Engine dynamometer measurements showed an increase in charge motion led to improved combustion stability, increased combustion efficiency, lower fuel consumption, and higher dilution tolerance. A CFD study was conducted using in-house models of spray and combustion to simulate the engine operating with and without valve deactivation. The computations demonstrated that the improved combustion was primarily driven by higher laminar flame speeds through enhanced mixing of internal residual gases, better containment of the fuel cloud within the piston bowl, and higher postflame diffusion burn rates during the initial, main, and late stages of the combustion process, respectively. DEWEY : 620.1 ISSN : 0742-4795 En ligne : http://asmedl.org/getabs/servlet/GetabsServlet?prog=normal&id=JETPEZ000134000009 [...]