Grain size–wear rate relationship for titanium in liquid nitrogen environment / Aditya Jain in Acta materialia, Vol. 58 N° 7 (Avril 2010)  

Public ISBD [article]  inActa materialia > Vol. 58 N° 7 (Avril 2010) . - pp. 2313–2323 Titre : Grain size–wear rate relationship for titanium in liquid nitrogen environment Type de document : texte imprimé Auteurs : Aditya Jain, Auteur ; B. Basu, Auteur ; B.V. Manoj Kumar, Auteur Année de publication : 2011 Article en page(s) : pp. 2313–2323 Note générale : Métallurgie Langues : Anglais (eng) Mots-clés : Wear Grain size Tribolayer Ti Résumé : This paper presents the results of sliding wear experiments conducted on high-purity titanium (Ti) against bearing-steel in liquid nitrogen (LN2; boiling point: 77 K) environment. Ti samples of three different grain sizes (9, 17 and 37 μm) were used to study the effect of hardness, derived from grain refinement as well as cryogenic test temperature, on the wear properties of Ti. In our experiments, a constant load of 10 N and sliding speeds of 0.67, 1.11 and 4.19 m s−1 were used. The coefficient of friction (COF) for this tribo-couple varied between ∼0.25 and ∼0.50. While a steady state was always achieved, a peak in the COF was always noted in case of coarse-grain (37 μm) Ti tested at a sliding speed of 4.19 m s−1. Under the investigated sliding conditions, the wear rate was found to be of the order of 10−3–10−4 mm3 N−1 m−1. The lowest wear rate was recorded in the fine-grain (9 μm) Ti at the highest sliding speed of 4.19 m s−1. The critical analysis of the worn surface topography reveals that the reduced wear rate was due to the formation of adherent and strain-hardened tribolayer. In order to show various dominant wear mechanisms of Ti, a qualitative map was developed in sliding speed–grain size space. Substructure evaluation revealed the formation of a dense array of deformation twins because of the plastic deformation, which often resulted in the subdivision of grains. DEWEY : 669 ISSN : 1359-6454 En ligne : http://www.sciencedirect.com/science/article/pii/S1359645409008593 [article] Grain size–wear rate relationship for titanium in liquid nitrogen environment [texte imprimé] / Aditya Jain, Auteur ; B. Basu, Auteur ; B.V. Manoj Kumar, Auteur . - 2011 . - pp. 2313–2323. Métallurgie Langues : Anglais (eng) in Acta materialia > Vol. 58 N° 7 (Avril 2010) . - pp. 2313–2323 Mots-clés : Wear Grain size Tribolayer Ti Résumé : This paper presents the results of sliding wear experiments conducted on high-purity titanium (Ti) against bearing-steel in liquid nitrogen (LN2; boiling point: 77 K) environment. Ti samples of three different grain sizes (9, 17 and 37 μm) were used to study the effect of hardness, derived from grain refinement as well as cryogenic test temperature, on the wear properties of Ti. In our experiments, a constant load of 10 N and sliding speeds of 0.67, 1.11 and 4.19 m s−1 were used. The coefficient of friction (COF) for this tribo-couple varied between ∼0.25 and ∼0.50. While a steady state was always achieved, a peak in the COF was always noted in case of coarse-grain (37 μm) Ti tested at a sliding speed of 4.19 m s−1. Under the investigated sliding conditions, the wear rate was found to be of the order of 10−3–10−4 mm3 N−1 m−1. The lowest wear rate was recorded in the fine-grain (9 μm) Ti at the highest sliding speed of 4.19 m s−1. The critical analysis of the worn surface topography reveals that the reduced wear rate was due to the formation of adherent and strain-hardened tribolayer. In order to show various dominant wear mechanisms of Ti, a qualitative map was developed in sliding speed–grain size space. Substructure evaluation revealed the formation of a dense array of deformation twins because of the plastic deformation, which often resulted in the subdivision of grains. DEWEY : 669 ISSN : 1359-6454 En ligne : http://www.sciencedirect.com/science/article/pii/S1359645409008593

Exemplaires

Code-barres	Cote	Support	Localisation	Section	Disponibilité
aucun exemplaire