Combustion characteristics of HCCI in motorcycle engine / Yuh-Yih Wu in Transactions of the ASME . Journal of engineering for gas turbines and power, Vol. 132 N° 4 (Avril 2010)  

Public ISBD [article]  inTransactions of the ASME . Journal of engineering for gas turbines and power > Vol. 132 N° 4 (Avril 2010) . - 04 p. Titre : Combustion characteristics of HCCI in motorcycle engine Type de document : texte imprimé Auteurs : Yuh-Yih Wu, Auteur ; Ching-Tzan Jang, Auteur ; Bo-Liang Chen, Auteur Année de publication : 2010 Article en page(s) : 04 p. Note générale : Génie Mécanique Langues : Anglais (eng) Mots-clés : Combustion Engines Internal combustion engines Motorcycles Petroleum Index. décimale : 620.1 Essais des matériaux. Défauts des matériaux. Protection des matériaux Résumé : Homogeneous charge compression ignition (HCCI) is recognized as an advanced combustion system for internal combustion engines that reduces fuel consumption and exhaust emissions. This work studied a 150 cc air-cooled, four-stroke motorcycle engine employing HCCI combustion. The compression ratio was increased from 10.5 to 12.4 by modifying the cylinder head. Kerosene fuel was used without intake air heating and operated at various excess air ratios (lambda), engine speeds, and exhaust gas recirculation (EGR) rates. Combustion characteristics and emissions on the target engine were measured. It was found that keeping the cylinder head temperature at around 120–130°C is important for conducting a stable experiment. Two-stage ignition was observed from the heat release rate curve, which was calculated from cylinder pressure. Higher lambda or EGR causes lower peak pressure, lower maximum rate of pressure rise (MRPR), and higher emission of CO. However, EGR is better than lambda for decreasing the peak pressure and MRPR without deteriorating the engine output. Advancing the timing of peak pressure causes high peak pressure, and hence increases MRPR. The timing of peak pressure around 10–15 degree of crank angle after top dead center indicates a good appearance for low MRPR. DEWEY : 620.1 ISSN : 0742-4795 En ligne : http://asmedl.org/getabs/servlet/GetabsServlet?prog=normal&id=JETPEZ000132000004 [...] [article] Combustion characteristics of HCCI in motorcycle engine [texte imprimé] / Yuh-Yih Wu, Auteur ; Ching-Tzan Jang, Auteur ; Bo-Liang Chen, Auteur . - 2010 . - 04 p. Génie Mécanique Langues : Anglais (eng) in Transactions of the ASME . Journal of engineering for gas turbines and power > Vol. 132 N° 4 (Avril 2010) . - 04 p. Mots-clés : Combustion Engines Internal combustion engines Motorcycles Petroleum Index. décimale : 620.1 Essais des matériaux. Défauts des matériaux. Protection des matériaux Résumé : Homogeneous charge compression ignition (HCCI) is recognized as an advanced combustion system for internal combustion engines that reduces fuel consumption and exhaust emissions. This work studied a 150 cc air-cooled, four-stroke motorcycle engine employing HCCI combustion. The compression ratio was increased from 10.5 to 12.4 by modifying the cylinder head. Kerosene fuel was used without intake air heating and operated at various excess air ratios (lambda), engine speeds, and exhaust gas recirculation (EGR) rates. Combustion characteristics and emissions on the target engine were measured. It was found that keeping the cylinder head temperature at around 120–130°C is important for conducting a stable experiment. Two-stage ignition was observed from the heat release rate curve, which was calculated from cylinder pressure. Higher lambda or EGR causes lower peak pressure, lower maximum rate of pressure rise (MRPR), and higher emission of CO. However, EGR is better than lambda for decreasing the peak pressure and MRPR without deteriorating the engine output. Advancing the timing of peak pressure causes high peak pressure, and hence increases MRPR. The timing of peak pressure around 10–15 degree of crank angle after top dead center indicates a good appearance for low MRPR. DEWEY : 620.1 ISSN : 0742-4795 En ligne : http://asmedl.org/getabs/servlet/GetabsServlet?prog=normal&id=JETPEZ000132000004 [...]

Exemplaires

Code-barres	Cote	Support	Localisation	Section	Disponibilité
aucun exemplaire