The port width and position determination for pressure-exchange ejector / Wenjing Zhao in Transactions of the ASME . Journal of engineering for gas turbines and power, Vol. 134 N° 6 (Juin 2012)  

Public ISBD [article]  inTransactions of the ASME . Journal of engineering for gas turbines and power > Vol. 134 N° 6 (Juin 2012) . - 04 p. Titre : The port width and position determination for pressure-exchange ejector Type de document : texte imprimé Auteurs : Wenjing Zhao, Auteur ; Dapeng Hu, Auteur ; Peiqi Liu, Auteur Année de publication : 2012 Article en page(s) : 04 p. Note générale : Génie mécanique Langues : Anglais (eng) Mots-clés : Pressure-exchange ejector Index. décimale : 620.1 Essais des matériaux. Défauts des matériaux. Protection des matériaux Résumé : A pressure-exchange ejector transferring energy by compression and expansion waves has the potential for higher efficiency. The width and position of each port are essential in pressure-exchange ejector design. A dimensionless time tau expressing both port widths and the positions of port ends was introduced. A prototype was designed and the experimental system was set up. Many sets of experiment with different geometrical arrangements were conducted. The results suggest that the efficiency greatly changes with the geometrical arrangements. The efficiency is about 60% at proper port widths and positions, while at improper geometrical arrangements, the efficiency is much lower and the maximum deviation may reach about 20%. The proper dimensionless port widths and positions at different operating conditions are obtained. For a fixed overall pressure ratio, the widths of the high pressure flow inlet and middle pressure flow outlet increase as the outlet pressure increases and the low pressure flow inlet width is reduced with a larger outlet pressure. The middle pressure flow outlet (MO) opening end remains constant at different outlet pressures. The positions of the high pressure flow inlet (HI) closed end and the low pressure flow inlet (LI) open end increase with the elevation of outlet pressure, however, the distance between the HI closing end and the LI opening end is constant. The port widths and positions have a significant influence on the performance of the pressure-exchange ejector. The dimensionless data obtained are very valuable for pressure-exchange ejector design and performance optimization. DEWEY : 620.1 ISSN : 0742-4795 En ligne : http://asmedl.org/getabs/servlet/GetabsServlet?prog=normal&id=JETPEZ000134000006 [...] [article] The port width and position determination for pressure-exchange ejector [texte imprimé] / Wenjing Zhao, Auteur ; Dapeng Hu, Auteur ; Peiqi Liu, Auteur . - 2012 . - 04 p. Génie mécanique Langues : Anglais (eng) in Transactions of the ASME . Journal of engineering for gas turbines and power > Vol. 134 N° 6 (Juin 2012) . - 04 p. Mots-clés : Pressure-exchange ejector Index. décimale : 620.1 Essais des matériaux. Défauts des matériaux. Protection des matériaux Résumé : A pressure-exchange ejector transferring energy by compression and expansion waves has the potential for higher efficiency. The width and position of each port are essential in pressure-exchange ejector design. A dimensionless time tau expressing both port widths and the positions of port ends was introduced. A prototype was designed and the experimental system was set up. Many sets of experiment with different geometrical arrangements were conducted. The results suggest that the efficiency greatly changes with the geometrical arrangements. The efficiency is about 60% at proper port widths and positions, while at improper geometrical arrangements, the efficiency is much lower and the maximum deviation may reach about 20%. The proper dimensionless port widths and positions at different operating conditions are obtained. For a fixed overall pressure ratio, the widths of the high pressure flow inlet and middle pressure flow outlet increase as the outlet pressure increases and the low pressure flow inlet width is reduced with a larger outlet pressure. The middle pressure flow outlet (MO) opening end remains constant at different outlet pressures. The positions of the high pressure flow inlet (HI) closed end and the low pressure flow inlet (LI) open end increase with the elevation of outlet pressure, however, the distance between the HI closing end and the LI opening end is constant. The port widths and positions have a significant influence on the performance of the pressure-exchange ejector. The dimensionless data obtained are very valuable for pressure-exchange ejector design and performance optimization. DEWEY : 620.1 ISSN : 0742-4795 En ligne : http://asmedl.org/getabs/servlet/GetabsServlet?prog=normal&id=JETPEZ000134000006 [...]

Exemplaires

Code-barres	Cote	Support	Localisation	Section	Disponibilité
aucun exemplaire