Documents disponibles écrits par cet auteur

Effervescent atomization of viscoelastic liquids / S. C. Geckler in Transactions of the ASME . Journal of fluids engineering, Vol. 130 N° 6 (Juin 2008) 

Public ISBD [article]  in Transactions of the ASME . Journal of fluids engineering > Vol. 130 N° 6 (Juin 2008) . - 11 p. Titre : Effervescent atomization of viscoelastic liquids : experiment and modeling Type de document : texte imprimé Auteurs : S. C. Geckler, Auteur ; P. E. Sojka, Auteur Année de publication : 2009 Article en page(s) : 11 p. Note générale : Fluids engineering Langues : Anglais (eng) Mots-clés : Fluids;  drops;  polymers;  sprays;  molecular  weight;  water;  stability;  tension Résumé : The effervescent atomization of viscoelastic liquids is reported. A total of 23 fluids, formulated from a 60wt% glycerine/40wt% water solvent to which were added varying concentrations (0.001–0.5wt%) of poly(ethylene oxide) polymers whose molecular weights ranged from 12,000 to 900,000, were sprayed through a conventional effervescent atomizer. Mean drop sizes were measured using a forward light scattering instrument. The drop size (D32) data show the expected decrease with an increase in air-liquid ratio by mass (ALR), the expected increase with an increase in polymer concentration, plus an increase with an increase in polymer molecular weight for most cases. However, no significant change in D32 was observed for polymer solutions whose molecular weights ranged from 12,000 to 35,000, suggesting the presence of a critical molecular weight below which spray performance is unaltered. This argues for two different factors controlling drop size: Polymer molecular weight is most influential at the highest polymer concentrations while polymer concentration is most influential at the lowest polymer concentrations. Analysis of the spray formation process was carried out using a ligament formation model previously developed for the effervescent atomization of Newtonian liquids coupled with a linear stability model for the breakup of viscoelastic liquid jets. The jet breakup model assumes that an unrelaxed axial tension exists within the fluid. A comparison of model predictions and experimental data indicates that the model predicts the observed dependencies of mean drop size on ALR, polymer concentration, and polymer molecular weight. Quantitative agreement is within 10–50% of experimental values in all cases. Finally, a shortcoming of the model is noted and a means of avoiding this limitation reported. En ligne : http://fluidsengineering.asmedigitalcollection.asme.org/Issue.aspx?issueID=27318 [...] [article] Effervescent atomization of viscoelastic liquids : experiment and modeling [texte imprimé] / S. C. Geckler, Auteur ; P. E. Sojka, Auteur . - 2009 . - 11 p. Fluids engineering Langues : Anglais (eng) in Transactions of the ASME . Journal of fluids engineering > Vol. 130 N° 6 (Juin 2008) . - 11 p. Mots-clés : Fluids;  drops;  polymers;  sprays;  molecular  weight;  water;  stability;  tension Résumé : The effervescent atomization of viscoelastic liquids is reported. A total of 23 fluids, formulated from a 60wt% glycerine/40wt% water solvent to which were added varying concentrations (0.001–0.5wt%) of poly(ethylene oxide) polymers whose molecular weights ranged from 12,000 to 900,000, were sprayed through a conventional effervescent atomizer. Mean drop sizes were measured using a forward light scattering instrument. The drop size (D32) data show the expected decrease with an increase in air-liquid ratio by mass (ALR), the expected increase with an increase in polymer concentration, plus an increase with an increase in polymer molecular weight for most cases. However, no significant change in D32 was observed for polymer solutions whose molecular weights ranged from 12,000 to 35,000, suggesting the presence of a critical molecular weight below which spray performance is unaltered. This argues for two different factors controlling drop size: Polymer molecular weight is most influential at the highest polymer concentrations while polymer concentration is most influential at the lowest polymer concentrations. Analysis of the spray formation process was carried out using a ligament formation model previously developed for the effervescent atomization of Newtonian liquids coupled with a linear stability model for the breakup of viscoelastic liquid jets. The jet breakup model assumes that an unrelaxed axial tension exists within the fluid. A comparison of model predictions and experimental data indicates that the model predicts the observed dependencies of mean drop size on ALR, polymer concentration, and polymer molecular weight. Quantitative agreement is within 10–50% of experimental values in all cases. Finally, a shortcoming of the model is noted and a means of avoiding this limitation reported. En ligne : http://fluidsengineering.asmedigitalcollection.asme.org/Issue.aspx?issueID=27318 [...]