Documents disponibles écrits par cet auteur

Comparison of nanosized gold-based and copper-based catalysts for the low-temperature water-gas shift reaction / Diogo Mendes in Industrial & engineering chemistry research, Vol. 48 N°1 (Janvier 2009) 

Public ISBD [article]  in Industrial & engineering chemistry research > Vol. 48 N°1 (Janvier 2009) . - P. 430-439 Titre : Comparison of nanosized gold-based and copper-based catalysts for the low-temperature water-gas shift reaction Type de document : texte imprimé Auteurs : Diogo Mendes, Editeur scientifique ; Hermenegildo Garcia, Editeur scientifique ; V. B. Silva, Editeur scientifique Année de publication : 2009 Article en page(s) : P. 430-439 Note générale : Chemical engineering Langues : Anglais (eng) Mots-clés : Water-gas  Gold  and  copper  Electron  microscopy  CO2  and  H2 Résumé : In this paper the catalytic performances for the low-temperature water−gas shift reaction of Au/TiO2 type A (from World Gold Council), Au/CeO2 (developed at UPV-CSIC), CuO/Al2O3 (from BASF), and CuO/ZnO/Al2O3 (from REB Research & Consulting) have been compared. The catalysts were characterized by different techniques such as Raman spectroscopy, BET surface area measurements, temperature-programmed reduction, and high-resolution transmission electron microscopy, which gave additional information on the redox properties and textural and morphological structure of the investigated samples. The performances of these catalysts were evaluated in a wide range of operating conditions in a micro packed-bed reactor. It was observed that the presence of reaction products in the feed (CO2 and H2), as well as CO and H2O feed concentrations, have significant effects on the catalytic performances. With a typical reformate feed the Au/CeO2 catalyst reveals the highest CO conversion at the lowest temperature investigated (150 °C). However, while in the long tests performed the CuO/ZnO/Al2O3 catalyst showed a good stability for the entire range of temperatures tested (150−300 °C), the Au/CeO2 sample clearly showed two distinct behaviors: a progressive deactivation at lower temperatures and a good stability at higher ones. The selection of the best catalytic system is therefore clearly dependent upon the range of temperatures used. En ligne : http://pubs.acs.org/doi/abs/10.1021/ie8010676 [article] Comparison of nanosized gold-based and copper-based catalysts for the low-temperature water-gas shift reaction [texte imprimé] / Diogo Mendes, Editeur scientifique ; Hermenegildo Garcia, Editeur scientifique ; V. B. Silva, Editeur scientifique . - 2009 . - P. 430-439. Chemical engineering Langues : Anglais (eng) in Industrial & engineering chemistry research > Vol. 48 N°1 (Janvier 2009) . - P. 430-439 Mots-clés : Water-gas  Gold  and  copper  Electron  microscopy  CO2  and  H2 Résumé : In this paper the catalytic performances for the low-temperature water−gas shift reaction of Au/TiO2 type A (from World Gold Council), Au/CeO2 (developed at UPV-CSIC), CuO/Al2O3 (from BASF), and CuO/ZnO/Al2O3 (from REB Research & Consulting) have been compared. The catalysts were characterized by different techniques such as Raman spectroscopy, BET surface area measurements, temperature-programmed reduction, and high-resolution transmission electron microscopy, which gave additional information on the redox properties and textural and morphological structure of the investigated samples. The performances of these catalysts were evaluated in a wide range of operating conditions in a micro packed-bed reactor. It was observed that the presence of reaction products in the feed (CO2 and H2), as well as CO and H2O feed concentrations, have significant effects on the catalytic performances. With a typical reformate feed the Au/CeO2 catalyst reveals the highest CO conversion at the lowest temperature investigated (150 °C). However, while in the long tests performed the CuO/ZnO/Al2O3 catalyst showed a good stability for the entire range of temperatures tested (150−300 °C), the Au/CeO2 sample clearly showed two distinct behaviors: a progressive deactivation at lower temperatures and a good stability at higher ones. The selection of the best catalytic system is therefore clearly dependent upon the range of temperatures used. En ligne : http://pubs.acs.org/doi/abs/10.1021/ie8010676